Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Eumir, the 9610007991 Dometic Connect Essential RV Thermostat RV-C #DMC79JF does not have the ability to control the two heat sources independently. It can control both but it does not have ability to pick between either.
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
Hello Kenneth, Thanks for writing in. I don’t have a database that shows exactly what was installed in every camper, but based on my research, your 2020 Transcend Xplor 243BH most commonly came with a 6-gallon Dometic (Atwood-style) water heater.…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Valterra RV door parts make it straightforward to refresh a worn screen slide or window frame. Match the shape and dimensions to your opening for a sure fit, and choose options like frosted/opaque glass or an ivory slider panel to suit your setup. A quick way to get your entry working and looking right again.
Some replacements do not include adhesive or a seal strip. Plan to provide a suitable sealant if your original had a gasket or tape. Reuse any intact factory seal where possible, and if missing, a careful bead of silicone can help seal the frame during install.
Valterra entry door window frame assemblies come with frosted/opaque glass. This lets in light while helping block visibility. If you specifically need clear glass, confirm the glass style in the specs or check if a glass-only option meets your preference.
Match your opening to the slide's shape and exact dimensions. Compare to sizes like 11-15/16" long x 11-13/16" wide or 11-7/8" wide x 11-11/16" long listed in the specs. Check whether you want a push-down knob or a plain slider—some options do not include a knob. Verify the slide style lines up with your door's track and screw layout before ordering.
It can, but check the clearance. Close the screen and main door together and measure the space around the handle area to compare with the slide's width and profile. If your original slide had extra relief around the handle, confirm the replacement has similar clearance to help prevent contact.