Filter by Style

$89.70 - $89.70

$70.69 - $361.30

$9.44 - $30.36

$22.21 - $559.99

$371.66 - $1,260.95
Videos
for Mooring
Help Articles
for Mooring
Expert Answers
for Mooring
Hello Dennis, You can use your current Chinese races, and just get the bearings from the Timken Bearing Kit, 14125A/25580 Bearings, 14276/25520 Races, GS-2125DL Seal #TMK32VR. You will want: - Inner bearing: Timken Replacement Trailer Wheel Bearing -…
view full answer...Since the tire height of your spare 185/80-13 is right at 24-1/2 inches the #CE27420 that you referenced would work well.
view full answer...Hey Mark, The Replacement Gas Strut for Roadmaster Tow Defender #RM-200023-50 is a 65lb gas strut.
view full answer...The closest axle we have to what you need is the part #20440I-EZ-60 which has very similar specs as what you need, but the spring center is off by one inch as it is 48 inches on this axle. The overall capacity is 2,000 lbs and the hub face to hub…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…
view full answer...A bearing, no matter where it is made, has to meet certain standards for use in the United States. With that said there are some cases where despite having to meet these standards, the US made product is better. When it comes to bearings though I…
view full answer...Thanks so much for the photo, which shows you have a UFP A-60 actuator, which is the same as the Dexter DX7.5L A-60 Brake Actuator - Drum #DX33FR. I can confirm that the correct replacement inner member for both actuators is the Replacement Inner…
view full answer...I went out to our warehouse to get the following dimensions for the Dexter Torflex #11 Axle Side-Mount Frame Installation Hardware Kit #DX57FR as we do not have a dimensional drawing from Dexter. The overall length is 11-7/16", height of side…
view full answer...After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…
view full answer...William yes, I can confirm that the Curt T-Connector Vehicle Wiring Harness #C88RV is what you'd need for your 2025 Chevrolet Equinox. If you're needing help with anything else, feel free to drop a comment before you go!
view full answer...Unless ShoreLand'r has a special wiring harness kit that has all of the connectors for your lights (which is very unlikely) you are looking at a complete custom job. You can either choose to replace the damaged wiring that you see with 16 Gauge…
view full answer...The UFP 34044 is basically the Dexter DX7.5L A-60 part #DX89FR. The second number you mentioned is actually a phone number. But the #DX89FR would be an exact replacement for what you have.
view full answer...Videos
for Mooring
Help Articles
for Mooring
Expert Answers
for Mooring
Hello Dennis, You can use your current Chinese races, and just get the bearings from the Timken Bearing Kit, 14125A/25580 Bearings, 14276/25520 Races, GS-2125DL Seal #TMK32VR. You will want: - Inner bearing: Timken Replacement Trailer Wheel Bearing -…
view full answer...Since the tire height of your spare 185/80-13 is right at 24-1/2 inches the #CE27420 that you referenced would work well.
view full answer...Hey Mark, The Replacement Gas Strut for Roadmaster Tow Defender #RM-200023-50 is a 65lb gas strut.
view full answer...The closest axle we have to what you need is the part #20440I-EZ-60 which has very similar specs as what you need, but the spring center is off by one inch as it is 48 inches on this axle. The overall capacity is 2,000 lbs and the hub face to hub…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…
view full answer...A bearing, no matter where it is made, has to meet certain standards for use in the United States. With that said there are some cases where despite having to meet these standards, the US made product is better. When it comes to bearings though I…
view full answer...Thanks so much for the photo, which shows you have a UFP A-60 actuator, which is the same as the Dexter DX7.5L A-60 Brake Actuator - Drum #DX33FR. I can confirm that the correct replacement inner member for both actuators is the Replacement Inner…
view full answer...I went out to our warehouse to get the following dimensions for the Dexter Torflex #11 Axle Side-Mount Frame Installation Hardware Kit #DX57FR as we do not have a dimensional drawing from Dexter. The overall length is 11-7/16", height of side…
view full answer...After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…
view full answer...William yes, I can confirm that the Curt T-Connector Vehicle Wiring Harness #C88RV is what you'd need for your 2025 Chevrolet Equinox. If you're needing help with anything else, feel free to drop a comment before you go!
view full answer...Unless ShoreLand'r has a special wiring harness kit that has all of the connectors for your lights (which is very unlikely) you are looking at a complete custom job. You can either choose to replace the damaged wiring that you see with 16 Gauge…
view full answer...The UFP 34044 is basically the Dexter DX7.5L A-60 part #DX89FR. The second number you mentioned is actually a phone number. But the #DX89FR would be an exact replacement for what you have.
view full answer...Filter Results
Buoy Rods
$89.70 - $89.70
Buoys
$70.69 - $361.30
Dock Lines
$9.44 - $30.36
Line Chafe Guards
$22.21 - $559.99
Whips
$371.66 - $1,260.95