Filter Products
(1)
(5)
Filter Results
Bench Vise
$56.31 - $250.84
Ratcheting Clamps
$5.94 - $8.09
Vise Mounts
$92.63 - $92.63
Hand Tools Parts or AccessoriesFilter by Tool Style
$56.31 - $250.84
$5.94 - $8.09
$92.63 - $92.63
Filter Results
Videos
for Hand Tools
Help Articles
for Hand Tools
Expert Answers
for Hand Tools
Yes, you can attach a LockNLoad platform to the bottom of the Yakima EasyRider Double Decker Trailer item #Y08129 but not that one because it's too wide. Instead you'll need the 84" Long x 49" Wide…
view full answer...Hello Greg, I cannot personally see any difference between the M40i and sDrive for the 2019 BMW X3. We haven't done an install on the M40i, so I can't say for sure what the difference would be regarding the #C99RV hitch and…
view full answer...Hey John, there's no reason you couldn't use the Blue Ox Wheel Chocks part #BLU47UR on all 4 wheels of your trailer as like a temporary lift. The pair alone has a 30k weight capacity as well so in that regard it would work…
view full answer...Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a…
view full answer...Hello Harlow, thanks for reaching out. We do have the Replacement Head #BXW4011 which fits the Blue Ox SwayPro Weight Distribution Systems. Regrettably we do not carry the bolts that go with this. Your will need grade 5 zinc-plated 3/4”-10 x 4” hex…
view full answer...Hey Tom, There is a bike rack I highly recommend for your 2024 Toyota Crown and the Curt Trailer Hitch #C77ZV, which is the Saris Freedom Bike Rack for 2 Bikes #SA4412B. What I love about this rack is its unique combination of being easy to handle…
view full answer...You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…
view full answer...Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…
view full answer...The Draw-Tite Max-Frame Trailer Hitch Receiver part #75600 which is a fit for a 2015 BMW X5 actually comes with the poly rivets that you'll need to use to reattach the fender trim. If you need the tool as well, we do carry one you can use…
view full answer...To replace a hitch ball on the Blue Ox SwayPro Weight Distribution #BLU66FR you will need a 1-7/8" 12pt Thin Walled Socket #ALL643216. This socket will fit inside the opening for the nut that fastens the hitch ball. The socket will require…
view full answer...Hey Dave, Looks like the BT-150 uses #L44649 bearings so you would be able to swap the hub out with the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-G-EZ-2K. This comes with a #10-9 grease seal, which has a 1.5" inner…
view full answer...Yes, the Powerbuilt Thin Walled Socket #ALL643216 or the Fastway/Equal-i-zer part #EQ70-00-4800 will allow you to properly torque the hitch ball in your Fastway weight distribution system #FA94-00-1000.
view full answer...
