Covers - Equipment Covers

Hey Sherri, thanks for all of the info from your RV door! Knowing all that yes the MORryde step part #MR48RR that you referenced would be the correct fit and will work great as a set of stairs to get in and out of your RV. What camper do you have?

The HammerBlow Trailer Coupler, like the #BD028463 is a coupler that will mount to the from frame of a trailer and be used to attach to a hitch ball on the back of a vehicle. It mounts to 50 degree A-Frame Tongue and will couple to a 2-5/16 in hitch…

Hey Michael! Since you were looking at the SoftStartRV Soft Start #SSR54FR are you wanting that built in as well? The Active Controls ActiveStart Plug-In Soft Start for RVs #AS94FR is a soft start and surge protector all in one. If you aren't…

For your utility trailer, there aren't specific covers made, however you can use a travel trailer cover for your application. I recommend the Adco Olefin HD RV Cover for Travel Trailers up to 18' - All Climate + Wind - Gray #AD37ZR or the…

Hey Hugo, going with a 30 amp MPPT solar charge controller like the part #RS25FR would be the best choice. This is probably rated most ideally for the solar panels you have currently and it's an MPPT style which does a really good job charging…

I drew up a diagram below that displays the dimensions from the center of the mounting points to the center of the crosstube so that you can measure and determine if the Curt Custom Base Plate Kit #C68FR would clear the bumper. In the attached video…

Hi Joe, I was able to get my hands on the Curt Custom Base Plate Kit #C68FR and found the distance from the center of the mounting holes down to the crosstube to be a half inch longer.

The Adco SFS AquaShed Cover for Bumper Pull Trailer part #290-46004 would be an excellent option for a 7 x 14 V-Nose Enclosed Trailer. The Adco SFS AquaShed Cover for Bumper Pull Trailers is actually designed for horse trailers but it will work well…

For your 7' x 16' V-Nose enclosed trailer I recommend the Adco SFS AquaShed Cover for Bumper Pull Trailer #290-46005. This is designed for trailers up to 18' long so you'll have a little bit of extra material for an easier fit. There…

Good question! Can you close the hatch of the vehicle the CVT Timber Creek Annex #RG35ZV is attached to? Yes. However, it should be noted that the hatch is actually acting as a roof support, so some of the roof will not necessarily cave in, but it…

The easiest way to determine what size and if you have a straight spindle is to remove one of the hubs. You will then be able to either find the numbers on the bearings to verify the correct replacement or measure the spindle diameters with a Digital…

For your Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers #CC-255, we have the Storage Cover for etrailer 4,500-Watt Generator #333-0010, which will fit generators measuring up to 18-7/8" long x 15-3/8" tall x 11-3/4"…

Hey Sherri, thanks for all of the info from your RV door! Knowing all that yes the MORryde step part #MR48RR that you referenced would be the correct fit and will work great as a set of stairs to get in and out of your RV. What camper do you have?

The HammerBlow Trailer Coupler, like the #BD028463 is a coupler that will mount to the from frame of a trailer and be used to attach to a hitch ball on the back of a vehicle. It mounts to 50 degree A-Frame Tongue and will couple to a 2-5/16 in hitch…

Hey Michael! Since you were looking at the SoftStartRV Soft Start #SSR54FR are you wanting that built in as well? The Active Controls ActiveStart Plug-In Soft Start for RVs #AS94FR is a soft start and surge protector all in one. If you aren't…

For your utility trailer, there aren't specific covers made, however you can use a travel trailer cover for your application. I recommend the Adco Olefin HD RV Cover for Travel Trailers up to 18' - All Climate + Wind - Gray #AD37ZR or the…

Hey Hugo, going with a 30 amp MPPT solar charge controller like the part #RS25FR would be the best choice. This is probably rated most ideally for the solar panels you have currently and it's an MPPT style which does a really good job charging…

I drew up a diagram below that displays the dimensions from the center of the mounting points to the center of the crosstube so that you can measure and determine if the Curt Custom Base Plate Kit #C68FR would clear the bumper. In the attached video…

Hi Joe, I was able to get my hands on the Curt Custom Base Plate Kit #C68FR and found the distance from the center of the mounting holes down to the crosstube to be a half inch longer.

The Adco SFS AquaShed Cover for Bumper Pull Trailer part #290-46004 would be an excellent option for a 7 x 14 V-Nose Enclosed Trailer. The Adco SFS AquaShed Cover for Bumper Pull Trailers is actually designed for horse trailers but it will work well…

For your 7' x 16' V-Nose enclosed trailer I recommend the Adco SFS AquaShed Cover for Bumper Pull Trailer #290-46005. This is designed for trailers up to 18' long so you'll have a little bit of extra material for an easier fit. There…

Good question! Can you close the hatch of the vehicle the CVT Timber Creek Annex #RG35ZV is attached to? Yes. However, it should be noted that the hatch is actually acting as a roof support, so some of the roof will not necessarily cave in, but it…

The easiest way to determine what size and if you have a straight spindle is to remove one of the hubs. You will then be able to either find the numbers on the bearings to verify the correct replacement or measure the spindle diameters with a Digital…

For your Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers #CC-255, we have the Storage Cover for etrailer 4,500-Watt Generator #333-0010, which will fit generators measuring up to 18-7/8" long x 15-3/8" tall x 11-3/4"…