Truck Bed Mats Specs:
Features:
...Heavy-duty truck mat protects truck bed from dings and dents Constructed with 1/2" thick rubber Non-slip checker plate design prevents cargo from shifting Heavyweight mat stay...
More Information >Truck Bed Mats Specs:
Features:
...enough to remove and reinstall with ease, the Access truck-bed mat offers your vehicle's bed the ultimate in protection and convenience. Whether you're at work or at play, this 1/2-inch-thic...
More Information >Truck Bed Mats Specs:
Features:
...enough to remove and reinstall with ease, the Access truck-bed mat offers your vehicle's bed the ultimate in protection and convenience. Whether you're at work or at play, this 1/2-inch-thic...
More Information >Truck Bed Mats Specs:
Features:
...the sides, wheel wells or tailgate of your truck bed Thickness: 1/2" Limited lifetime warranty The BedRug truck-bed mat protects your fragile cargo and the floor of your vehicle's bed fro...
More Information >Truck Bed Mats Specs:
Features:
...enough to remove and reinstall with ease, the Access truck-bed mat offers your vehicle's bed the ultimate in protection and convenience. Whether you're at work or at play, this 1/2-inch-thic...
Installation Notes:
Does not fit on vehicles with a Flareside or Stepside bed
More Information >Truck Bed Mats Specs:
Features:
...the sides, wheel wells or tailgate of your truck bed Thickness: 1/2" Limited lifetime warranty The BedRug truck-bed mat protects your fragile cargo and the floor of your vehicle's bed fro...
Installation Notes:
Does not fit in Flareside or Stepside models
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…
view full answer...The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...For a 2023 GMC Canyon we currently offer the BedRug Custom Full Truck Bed Liner #BR76ZR, which will fully cover the bed, bedrails, bulkhead, and tailgate. It's made of a…
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article…
view full answer...The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge…
view full answer...The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the ones…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will…
view full answer...I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too…
view full answer...The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system…
view full answer...Filter Products (12)