# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 3
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 4
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 5
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 6
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 7
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
# 8
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.
# 9
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 10
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 11
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 12
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
The team at etrailer relayed helped find the right solution. Using this ball mount fixed the height issue I had with my SUV not lining up with the trailer. Very grateful for their help.
Works great!! I always order from etrailer Customer service and fast delivery
# 13
Draw-Tite Ball Mount for 2" Hitches - 5" Rise, 6" Drop - 10-1/4" Long - 16K
Its been a year and I aint broke it yet. I use this hitch to tow my 7Klb trailer. The trailer is tongue heavy and I needed something rugged to tow it with. Haven't had any troubles with this hitch.
This ball mount fit the SUV just right. I needed a 5 inch rise and the mount angled away from the bumper. However, the load capacity was way more than I needed, but the fit made up for that. It's a little loose in the receiver so I will be adding a stabalizer to lock it in place.
# 14
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
Product is exactly as described on the etrailer.com website and measurements and dimensions fit perfect. Easy phone order process and prompt delivery, standard shipping arrived 3 business days after the order was placed. The extra long version of the ball mount makes it perfect for me to put on the bike rack while towing my horses.
# 15
Curt Ball Mount for 2" Hitches - 7" Rise, 8" Drop - 9-3/8" Long - 12,000 lbs
This ball mount has served it purpose well. I purchased a new travel trailer that is heavy enough to require a weight distribution hitch when using the factory installed Class III hitch on our Dodge RAM 2500. I decided to upgrade to a Class V hitch combined with this ball mount to take delivery of the TT in order to defer decisions about a WD hitch until the actual load conditions were known. The hour trip home with this setup worked very well. Once the trailer was outfitted I was able to determine the actual tongue weight of the loaded trailer and I decided to purchase an appropriately sized Reese Straight Line WD hitch. However, this ball mount comes in handy for moving the trailer short distances without hassling with the WD system. The purchase experience through etrailer.com was first rate.
I was surprised at the heft and quality of the ball mount. Shipping was fast, communication good, easy and informative website to use. Thanks etrailer, you have earned a new customer!
# 16
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 17
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 18
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 19
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".
Each time we go camping we look for ways to improve the experience, the C45230 will allow us run with a short or long ball mount, the longer extension allows me to open my tail gate without disconnecting from the trailer. I looked at other manufacturers but was only able to find what I was looking from CURT, and etrailer offered the best price.
# 20
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
tl;dr good experience with warts. The etrailer-branded ball mount kit I ordered was back-ordered for a month, which was fine. Eventually Ashley E told me it would be a _second_ month. Not fine. She helped me configure a new order of third party parts. Shipped in one day. Great! Not great: Parts were just thrown in a box with no protection. UPS did their usual thing. Paint was chipped in a couple of places; would surely rust. I'll shoot these spots with some spray paint before installation. Hope that's a fix. I can't afford to diddle with a return.
Ordered the ball mount on Thurs and it arrived Monday. George emailed me Friday and said thanks for ordering again, I had ordered a full hitch the week before, so he expedited shipping on this item. I have ordered many times from etrailer and they have never disappointed. GREAT CUSTOMER SERVICE!!
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."