# 1
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We used this on our 2012 Sienna AWD to pull the largest single axle closed top U-Haul trailer to move furniture and bikes 400 miles through the mountains of PA, WV, and VA with no trouble. I noticed less jerking from the hitch being transferred to our van than the last time I towed a trailer like this (though that was with a large sedan). Easy to install and seemed to have decent tolerances in regards to fit and finish. Definitely increased my confidence in towing with a light duty vehicle.
Love the ball mount. I have a Toyota Sienna and the rear seats recess into a well, therefore the receiver hitch much go underneath the well. This means the ball mount enters the receiver approximately 10 inches off the ground. By using the ball mount to raise the ball, this makes the ball around 22 inches off the ground, which is recommended height for my trailer. My only regret is that I did not request you attach a ball as I did not have any wrenches large enough to fasten it. Again, the mount is great. Thanks, Ron Baker
# 2
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Exactly as advertised. No problems. I used it on a Toyota Sienna, which has a very low hitch receiver. I'm pulling a small utility trailer.
Came quicker than expected. All good .
# 3
Draw-Tite Ball Mount - 9-3/4" Rise, 11" Drop - 9" Long - 3,500 to 5,000 lbs
I bought a hitch, stinger, ball and wiring harness for my 2004 Toyota Sienna. It was delivered fast, it was the right stuff, and it fit, just like it was supposed to. It really was as easy to install as it looked in your video. The video was immensely helpful too. The video showed me exactly what I needed to know to get my hitch installed correctly and it gave me the confidence to order online and do it myself. The only drawback is a loss of ground clearance but you warned me fair and square up front about that, so I can hardly complain. Thank you, that was a good investment.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
I bought a hitch, stinger, ball and wiring harness for my 2004 Toyota Sienna. It was delivered fast, it was the right stuff, and it fit, just like it was supposed to. It really was as easy to install as it looked in your video. The video was immensely helpful too. The video showed me exactly what I needed to know to get my hitch installed correctly and it gave me the confidence to order online and do it myself. The only drawback is a loss of ground clearance but you warned me fair and square up front about that, so I can hardly complain. Thank you, that was a good investment.
# 5
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
I had trouble finding a 4-3/4" rise at any local stores. Etrailer shipped it out in a reasonable amount of time. Using this to pull a small trailer behind a Toyota Sienna and needed the 4-3/4" rise. Packaging needs some thought. 2" ball was coming out the side of the box when it was received.
# 6
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
Very sturdy product but hole for the ball was drilled off center - shifted 1/16" to the side. etrailer kindly replaced the original after seeing a picture showing the fault.
Quality, strength and value describe not only this product but the entire etrailer experience. Product selection features, clean website and buying confidence. This ball mount is exactly what I expected and the express delivery was a bonus. This is my second experience etrailer and it probably won't be my last.
# 7
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
We used this on our 2012 Sienna AWD to pull the largest single axle closed top U-Haul trailer to move furniture and bikes 400 miles through the mountains of PA, WV, and VA with no trouble. I noticed less jerking from the hitch being transferred to our van than the last time I towed a trailer like this (though that was with a large sedan). Easy to install and seemed to have decent tolerances in regards to fit and finish. Definitely increased my confidence in towing with a light duty vehicle.
Love the ball mount. I have a Toyota Sienna and the rear seats recess into a well, therefore the receiver hitch much go underneath the well. This means the ball mount enters the receiver approximately 10 inches off the ground. By using the ball mount to raise the ball, this makes the ball around 22 inches off the ground, which is recommended height for my trailer. My only regret is that I did not request you attach a ball as I did not have any wrenches large enough to fasten it. Again, the mount is great. Thanks, Ron Baker
# 8
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
Wasn't sure if this is going to work on our 2009 Toyota sienna, but it's just right. The 5 1/2 inch height was perfect for a double axle ATV trailer. Item is quality made and etrailer shipped fast!
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Quality, strength and value describe not only this product but the entire etrailer experience. Product selection features, clean website and buying confidence. This ball mount is exactly what I expected and the express delivery was a bonus. This is my second experience etrailer and it probably won't be my last.
Fits perfect. Now my trailer is not hanging down anymore. It's level when it's hooked up. Thank you.
# 10
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
We used this on our 2012 Sienna AWD to pull the largest single axle closed top U-Haul trailer to move furniture and bikes 400 miles through the mountains of PA, WV, and VA with no trouble. I noticed less jerking from the hitch being transferred to our van than the last time I towed a trailer like this (though that was with a large sedan). Easy to install and seemed to have decent tolerances in regards to fit and finish. Definitely increased my confidence in towing with a light duty vehicle.
Love the ball mount. I have a Toyota Sienna and the rear seats recess into a well, therefore the receiver hitch much go underneath the well. This means the ball mount enters the receiver approximately 10 inches off the ground. By using the ball mount to raise the ball, this makes the ball around 22 inches off the ground, which is recommended height for my trailer. My only regret is that I did not request you attach a ball as I did not have any wrenches large enough to fasten it. Again, the mount is great. Thanks, Ron Baker
# 11
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
No issues or problems. Everything was as described.
# 12
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
Paint on draw bar was a little questionable. But it came that way from the manufacturer! Had nothing to do with Etrailer quality of service!
etrailer shipped fast and had great communication. The hitch was built very well look like a quality product and was just what I needed. The 5 inch rise was perfect for our 2009 Toyota sienna.
# 13
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Not a lot to say abou this other than the build quality and finish being excellent. As I said with the other part to this 3 part order, this company is Excellent to do business with. Professional. Great follow up.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 14
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
Paint on draw bar was a little questionable. But it came that way from the manufacturer! Had nothing to do with Etrailer quality of service!
etrailer shipped fast and had great communication. The hitch was built very well look like a quality product and was just what I needed. The 5 inch rise was perfect for our 2009 Toyota sienna.
# 15
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Exactly as advertised. No problems. I used it on a Toyota Sienna, which has a very low hitch receiver. I'm pulling a small utility trailer.
Came quicker than expected. All good .
# 16
Curt Ball Mount for 2" Hitches - 7" Rise, 8-1/4" Drop - 9-3/8" Long - 10,000 lbs
Fast shipping! Very nice product! Great customer sevice! Highly recommend! Thank you!!!
Was needing a 7-8 inch ride for my camper that could sustain a GVW of at least 5000 lbs. Let me say, it’s a hard to find item. Thankfully I called Etraer and with some research, found me the perfect ball mount. It’s heavy duty for a reasonable price.
# 17
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
Paint on draw bar was a little questionable. But it came that way from the manufacturer! Had nothing to do with Etrailer quality of service!
fits like a glove. works perfectly
# 18
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
# 19
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Love the ball mount. I have a Toyota Sienna and the rear seats recess into a well, therefore the receiver hitch much go underneath the well. This means the ball mount enters the receiver approximately 10 inches off the ground. By using the ball mount to raise the ball, this makes the ball around 22 inches off the ground, which is recommended height for my trailer. My only regret is that I did not request you attach a ball as I did not have any wrenches large enough to fasten it. Again, the mount is great. Thanks, Ron Baker
Prompt delivery, looks great.
# 20
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
Plugged right in. Worked great on my 2008 Toyota Sienna Van. Great information on correct size. Easy. Thanks
Flipped it for hight on a Toyota Sienna 2015 - Works Great!
What our customers are saying:
"I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex"