# 1
Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 10-1/8" Long Equalizers
They seem too wide for the springs on my 7,000 axle.
excellent quality replacement repair parts at a great price.
# 2
Replacement U-Bolt for 2" Wide, Square Axles - 7/16" Diameter - Zinc Plated
Exactly what I needed...delivery was spot on...thank you!
Parts looked good.
# 3
Dexter Trailer Springs Over-Under Conversion Kit
Our trailer was so low...that it could not make it up a low curb and some driveways - especially when fully loaded. Went with the Dexter axle flip kit. The Dexter bracket and base plate pieces are worth the extra $20-$30 compared to other similar kits - they make fitment easier, eliminate any guesswork on placement, and decrease installation time because of it. Took 2-3 relaxed pace hours for us to do single axle install. Tools required were ratchet/wrench set (13/16 deep socket worked for us for most of the bolts), cheater bar (for working those rusty bolts off), drill, angle grinder (cutter disc for oem u-bolts and leaf spring bolts that are rusted or welded in place, stripper disc for cleaning area around new bracket for welding) welder, floor jack and jack stands. We had to remove the leaf springs, as the wheel mount brackets would not fit through the openings. Was hoping we wouldn’t have to, but it was pretty simple to do. We jacked the trailer up. Removed the wheels. Removed the axle. Cleaned the axle area where new brackets go. Set the height and placement of the new Dexter brackets. We left the OEM brackets on the axle and placed the Dexter ones in the exact same position 180 degrees on the other side. Welded them on. Reinstalled leaf springs. Reinstalled axle, reinstalled wheels. Then voila! We added 6 full inches of height. Super awesome.
Great conversion kit, easy to get the plates lined up perfectly. I welded the new saddles onto the axle and welded the nuts to the bolts so there is zero chance of anything moving. Having the plates held in perfect position while welding made it simple. Solved the "dragging wheels problem" without having to cut off and reweld the fenders (which had been welded without enough clearance to the tires at the factory.)
# 4
Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs - 1-1/2" Tall Front
Good steel easy weld. The holes line up great
Arrived quickly and was as pictured. Correct application and welded nicely. Trailer is successfully back in operation now for about 9 months.
# 5
Torflex Lift Kit - Single Axle - 2-5/8" Lift
Perfect fix! Lifted up the camper just right for the 2 gray tanks I installed this past winter. Install was as per the instructions.
The trailer is a Palomino Solaire 147x. Installation was straightforward. The lift in combination with taller wheels and tires accomplished the desired ride height.
# 6
Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear
Shipped fast looks good will be putting it on my trailer this weekend.
I bought the spring kit to put on my home built trailer that I put my old heavy slide-in camper on. It more than met my expectations. There was no sway at 75mph or on the 5 mile trail back to camp.
# 7
Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
Great fit. I called to ask what I needed and etrailer made the right suggestions. Fast and friendly service for you trailer needs.
Rec'd item quickly along with new wheels I purchased. Items were packed very well. I installed my new wheels, tires, and equalizer kit the following weekend and my trailer was ready to go.
# 8
CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
Arrived well packed and as advertised. I'm going to pull the azle out of the boat trailer and wanted to have this 'on hand' should I break some of my U bolts. I've bought from you before - always been happy, thanks
Worked perfect for mounting a storage box to my boat trailer.
# 9
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 7/8" Rear
I am sorry but I can not remember names but I talked with two very helpful ladies and could not have been happier with their assistance. Thanks again, the trailer build is going great.
My 6' x 10' landscape trailer was a homemade by a prior owner. While it was mostly constructed very well, the spring hangers were not correct. The spacing for the springs was also wrong, and it had very little fender clearance. There was also evidence that the spring U-bolts had contacted the frame on occasion. (I do not carry loads anywhere near the 3500# axle rating.) I added an extra set of holes on the front hangers in case the ride height proved to be too much, but I like the way it sits with the stock holes. I don't think I'll be utilizing the extra holes. This kit was just the ticket to increase the suspension travel and fender clearance on my landscape trailer. Now it "sits right"!
# 10
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
Good kit with the necessary parts to replace leaf spring suspension. I welded the hangers rather than bolting them. The parts are not coated for the price point so you will need to paint them or they will rust immediately.
# 11
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
Excellent, had everything I needed and more for my trailer. Everything fit well!
This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!
# 12
Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
These hangers are great for the center. They provide just enough clearance for your equalizer. Because of the length and being that I am a welder I added a support inside the hanger to keep them rigid!
Megan was very helpful with helping get this order together and communicating with parts being shipped from other locations. Thank you so very much Megan!!!!
# 13
Replacement Shackle Strap - 2-5/8" Long
I was very disappointed when I received the shipment from etrailer and only half the parts were there. When I made the order I was told everything was in stock and would be shipped.
Easy installation holding up well.
# 14
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
These were purchased to assist with raising a dual-axle travel trailer. They arrived well packaged, and looked to be well made.They took readily to welding, so there was no issue with inferior material. The attached images show them being welded side-by-side to the frame rail extensions, then the entire assembly attached to the main frame.
My order was supposed to arrive on Saturday by Monday evening I had not received it I called the lady was very apologetic and said she would research it. She took care of everything and it was here. They were very helpful .!! the part was exactly what I needed Would definitely recommend them for their personnel and their follow up
# 15
Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
New bolts made replacement of springs easy
Good quality shackle bolts. Would buy again!
# 16
U-Bolt Plate - 3" Diameter, Round Trailer Axle - 1-3/4" Wide Spring - 1/2" Bolts
worked great during instalation
Just what I needed for my trailer build. I like the fact they are nice and thick (about .20” thick). Remember to prime and paint so they don’t rust out.
# 17
U-Bolt Plate - 3" Diameter, Round Trailer Axle - 2" Wide Spring - 1/2" Bolts
Exactly as described. Best price I could find and fast shipping
# 18
SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Overslung
I made some brackets to bolt to the frame. Now I have 100% contact with the Sumo Springs. The are working extremely well!
Help a lot with the bounce from the leaf springs
# 19
MORryde 14-3/4" Shock Absorbing Equalizers for Tandem Axle Trailers w/ 42" Wheelbase - 8K
I have not towed with it yet. But the installation went pretty smooth. I also installed the Morryde shackle kit. Everything looks heavy duty. The only thing is that 4 of the wet bolts were too long. I had to add 1/2 inch thick heavy duty washers to pull the Splined end of the bolts in. Shipping was good as always.
After 1 year and several trips…awesome!!! However I also installed a”wet” bolt kit and shocks…. W-H-A-T a difference!!! All from etrailer. All trailers should come like this!! 2021 271RL Salem Hemisphere
# 20
Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 6K to 8K
Looked at another brand, decided I liked the Lippert better. Although it was $[XX] more than where I started I was willing to pay the extra due to it having a variable width and it being heavier built than the product I was looking at. Paula was excellent in assisting me with this product, (4) springs, u bolts, wet blots / shackle kit.
These will be going back. Lippert did a terrible job prepping these for shipment. They showed up with evidence of metallic grinding, dropping, and less than a quality piece. The bubble wrap that was around the pieces wouldn’t protect a Christmas ornament from the dollar tree. Definitely not going on my trailer like this.
What our customers are saying:
"very easy to shop"