# 1
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
Nice solid (not hollow) and WELDED hitch. Have logged about 5,000 miles this year with no problems. I had many problems with bolted on balls, welded hitches are the way to go.
Exactly what I needed for my new Subaru hitch and quick delivery. Fusion ball mount nice feature..no need to remember to tighten before each use.
# 2
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 3
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 4
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 2,000 lbs
I purchased two drawbars for my Polaris ATV. Good quality and very fast shipping from etrailer.
This is the second hitch I have purchased from etrailer and, again, it was a perfect fit. Everything I buy from here is exactly what they say it is and exactly what I was needing. I will always recommend etrailer, they have never let me down. Gene Houston Texas area.
# 5
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.
# 6
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
Purchased for a 2006 Jeep liberty. the only issue I have is that it connects right below the spare tire, making trailer attachment more difficult that it should be. If I had gotten a slightly longer hitch, wouldn't have been an issue. It's not a deal breaker, and the hitch itself has works perfectly.
I haul a 5.5x10 open trailer w/ a 900 lb. ZTR, a push mower, and a handful of other tools 3 days a week. It is what it is. It does the job, no problem. A little finish wear and rust on the ball, but nothing major. I LIVE ON A DIRT ROAD, which is probably responsible for the wear.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 8
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
Works perfectly. Fast shipping. Very Satisfied.
# 9
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 10
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 11
Curt Class I Drawbar - 5" Rise - 11-9/16" Long - 2,000 lbs
This drawbar was exactly what I needed with the 5" rise. I use it to tow my boat. My car is low to the ground so the rise was just what I needed. The drawbar is very durable as well. When I was out on my boat a hit and run was done on my trailer. The trailer was pushed into my car and both were moved about 3 feet forward. The drawbar didn't break in half. It was bent but it prevented any damage to the rear of my car because of the quality construction of the drawbar.
# 12
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 13
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
# 14
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 6-3/4" Long - 2,000 lbs
I wrote 2 days ago and haen't heardafom anyone so I guess you only want reviews-. Here is what I wrote Steve, the class 1 hitch doesn’t fit the trailer hitch either. I don’t understand the continuing problem with all of the Curt hitches we have tried including the last draw hitch you selected and shipped, which I now need to return after H. Idalia passes, I want to point out that I initiially ordered somewhere on line a Maxxhaul adapter so I could move my 2” trailer until I sell it and it fit perfectly. I NEVER expected to have so much trouble getting a ball hitch to fit the 1.25 hitch recommended by etrailer for my car. Aren’t you glad I am writing an email rather than make star comments? I know that someone writes these things for ‘you’ and you don’t necessarily do the hands on so please direct this problem to someone who is supposed to make these product directives and solve this $[XX] attractive trailer hitch problem so I can haul my lawnmower in for repairs when needed on my utility trailer designed for doing so. Doesn’t Drawtite have a ball hitch for level hauling a trailer rather than Curt which is too thick. The powers that be need to rethink OD (outside diameters) vs ID (inside diameters) in their trailer connectors, screw the rattling! PS don’t forget arrangements for the return of the recommended draw hitch.
Great price! Amazingly fast service! The drawbar was a very tight fit in the hitch until I scraped off some of the paint at the end; then it was perfect.
# 15
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 16
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
Delivered missing the retaining clip
Keep with spare tire out of weather to prevent rust.
# 17
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 18
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
2024 CRV. Pretty straightforward install. The fish wires in the kit are a fantastic solution to holding the bolts. Thanks!
# 19
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Allows me to open the tailgate on the truck with a trailer hitched up.
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
# 20
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."