# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
EZ installation, plan on towing my 1932 plymouth coupe to car shows around the state.
Clean finish look and easy to install. If you order one read closely. It comes with a pin for it already. No meed to order one separately.
# 2
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Fits and works great
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 3
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Should work great! Had to extend the hitch since the bike rack hit the bumper on the Traverse.
The receiver is exactly what I was looking for. Put it on a 2016 chevy traverse and it is the right length for pulling a trailer. Looked at 6 1/2 inch, too short. Quality is good also. I give it 4 stars.
# 5
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Good product. Performs as described.
All the hardware fit and easy to follow instructions. Hitch is installed. Just need to put it to use now.
# 6
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Great product, but did not fit on my 2014 Traverse. The top receiver would rub on my fiberglass bumper of the Traverse and therefore only half the pin hole would line up with the receiver. Plus my 4 bike rack would not fit between car and pop up camper then.
Didn't take my husband long to install it on my vehicle. The only thing is that NO PIN comes with it so be sure to add one to your shopping cart as well. Heavy duty and everything worked as it should. Shipping was quick and notifications were received. The company followed up to make sure everything was good. This is what online, custom shopping experiences should be like.
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 8
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
It works!
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
# 9
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 10
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
High quality hitch for the price .
# 11
Curt Ball Mount for 2" Hitches - 6-1/4" Rise, 7-1/2" Drop - 13" Long - 5,000 lbs
All the hardware fit and easy to follow instructions. Hitch is installed. Just need to put it to use now.
What can I say amazing service I ordered a ball mount on the evening of the 26th and it was waiting for me at my house on the 27th. Used information on etrailer website to figure out what size and length I needed and got a perfect fit. Well done etrailer and they kept me informed by email before and after delivery. TOP NOTCH
# 12
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 13
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
All the hardware fit and easy to follow instructions. Hitch is installed. Just need to put it to use now.
What can I say amazing service I ordered a ball mount on the evening of the 26th and it was waiting for me at my house on the 27th. Used information on etrailer website to figure out what size and length I needed and got a perfect fit. Well done etrailer and they kept me informed by email before and after delivery. TOP NOTCH
# 14
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
All the hardware fit and easy to follow instructions. Hitch is installed. Just need to put it to use now.
What can I say amazing service I ordered a ball mount on the evening of the 26th and it was waiting for me at my house on the 27th. Used information on etrailer website to figure out what size and length I needed and got a perfect fit. Well done etrailer and they kept me informed by email before and after delivery. TOP NOTCH
# 15
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
# 16
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12" Long - 5,000 lbs
The receiver is exactly what I was looking for. Put it on a 2016 chevy traverse and it is the right length for pulling a trailer. Looked at 6 1/2 inch, too short. Quality is good also. I give it 4 stars.
Should work great! Had to extend the hitch since the bike rack hit the bumper on the Traverse.
# 17
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
Should work great! Had to extend the hitch since the bike rack hit the bumper on the Traverse.
What our customers are saying:
"Very easy process, good prices and my products were shipped on time and were delivered on time. The instructional videos online helped make installation easy!"