1997 Chevrolet Suburban Brake Controller

Features:

The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This proportional brake controller has simple controls and a digital display for diagnostic information. Includes 3 boost levels, a slide-bar manual override, built-in battery protection, automatic leveling, and continuous diagnostics.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

The large, digital, LED display and clearly labelled buttons on this proportional controller make it easy to use. Includes 3 levels of boost, a slide-bar manual override, built-in short circuit protection, and automatic leveling.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This proportional brake controller automatically syncs to your vehicle's computer network for smooth, precise braking. Low-speed brake adjustment gives you 2 settings for different speeds. Plug-and-play controller mounts in any direction.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

Simple and rugged, this time-delay brake controller is able to install in any direction, even upside down. Includes a large digital display with a dark smoke lens that can be read even in direct sunlight. Activates brakes with a preset intensity.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The plug-and-play unit mounts under your dashboard, out of sight and out of your way.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.

Features:

This brake controller likes to keep things simple, with a thumbwheel on the front to adjust the output settings and a lever on the side for the sensitivity. The digital display is large and simple so you can read it with just a glance.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.

You may also need a 4-Flat connector to complete your wiring.