I think we have just what you are looking for. Check out our Stake Pocket Tie-Down Anchor, # WFSPDR. This anchor mounts in the stake pockets on your trailer and gives you a d-ring tie-down point. These will work great with the Bulldog Winch Tie-Down Straps, # BDW20230 and they have a weight capacity of 4,000 lbs per anchor, which is as much capacity as you will get out of pretty much any stake pocket anchor.
I attached a photo that one of our other customers submitted using these stake... view full answer...
If the inner width of your flatbed trailer's stake pockets are 3-1/2" then you're going to want the Brophy Stake Pocket Tie Down Anchor item # TL2B you were looking at. The dimensions are 8-1/4" tall x 3-1/2" wide x 1-1/2" deep.
This tie down anchor will go through your stake pocket and will be secured by a pin that goes through the bottom. Each tie down anchor has a 4,000 lbs capacity. The Brophy Stake Pocket Tie Down Anchor item # TL2B is made in the USA and weighs 5 lbs. I have linked... view full answer...
Yes, 4 of the Brophy # SS15-C Tie anchors can work to secure your 67 Ford Sports Coupe.
Tie-down anchors must be chosen according to their safe working load limit (WLL). The weight of the secured cargo must not exceed the combined WLL of the anchors being used. For example, if you are using anchors # SS15-C anchors with a WLL of 1,600lbs each to tie down a load weighing 3,000 lbs, then you need at least 2 anchors to safely secure that load. It is recommended that you always use anchors... view full answer...
I am happy to tell you that four of the Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs # T55B that you ordered will indeed be strong enough to handle the 4,400 lb car you are going to haul.
The working load limit (WLL) is 1,600 lbs, and the way WLL works is that the weight of the cargo cannot exceed the combined capacity of the anchors. So you have plenty of room to spare with four of the Stake Pocket Tie-Down Anchor # T55B.
In regards to the last part of your... view full answer...
The Bulldog Winch Ratcheting Wheel Tie-Down Strap # BDW20362 is designed to connect to a D-Ring type of connection point so you wouldn't need to install an e-track on your trailer.
For your application I recommend installing the Brophy D-Ring Tie Down Anchor w Backing Plate # RR5K for your anchor points since you want them to be directly in-line with your tires and not offset like your current tie-down anchors. The Brophy kit mentioned above comes with a backing plate and installation... view full answer...
Without knowing what you're going to be hauling and tying down I can't really get too specific with a recommendation. I would install a minimum of 6 of the etrailer D-Ring Tie Down Anchor item # RRING-Q6000 on each side. How far out from the wall you want to go is up to you but I would space these out evenly along the length of the trailer.
For the etrailer D-Ring Tie Down Anchor item # RRING-Q6000 you will need to use the Backing Plate item # BP05. This will increase surface area for... view full answer...
Good evening! The Brophy Stake Pocket Tie Down Anchor item # TL2B you were looking at is going to be your best option. They fit the standard 2" x 4" stake pocket, have a 4,000 lbs capacity each, and measure 8-1/4" tall x 3-1/2" wide x 1-1/2" deep. These are sold individually.
This tie down anchor will go through your stake pocket and will be secured by a pin that goes through the bottom. The Brophy Stake Pocket Tie Down Anchor item # TL2B is made in the USA and weighs 5 lbs.
I have... view full answer...
The bolt that comes with the Brophy D-Ring Tie-Down Anchor with Backing Plate # DR1S has a diameter of 9/16 inches, so this would be the approximate size of the hole in the backing plate as well.
I have added a link to a video review for you to check out of the Tie-Down Anchor with Backing Plate # DR1S. view full answer...
We do offer many weld-on D-ring tie-downs for cargo control on trailers. These are shown on the linked page. All of these items are made of steel, not aluminum. It is not easy to weld steel and aluminum (due to the two metals' different melting points) but a skilled professional welder should be able to do it.
If you prefer to avoid the complication of welding you might consider the bolt-on D-rings shown on the other linked page. For example, Brophy offers various sizes such as # SR15-C... view full answer...
For a flat aluminum trailer tie down, I recommend the Tow-Rax Low-Profile Floor Track for Tie-Down Anchors - Aluminum - 6' Long - Machined - Qty 1 # TWSP72TA along with the Tie-Down Anchor for Tow-Rax Low-Profile Floor Track - 1,666 lbs - Qty 1 # TWSPDSTD225.
I don't recommend using the DISCONTINUED Draw-Tite Truck Bed Stake Pocket Chrome Anchor Points 92509. You want to be very careful about galvinic corrosion when using dissimilar metals. These may work well because of the rubber... view full answer...
The Replacement BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets # BU57FR are replacement tie-downs for the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets # BU88FR and # BU28FR which fit select Ford models.
For your 2004 Toyota Tundra you will want to use the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets # BU75FR (4 pk.) or the Replacement BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets # BU99FR (2 pk.) which are... view full answer...
Sounds like you are looking for D-Ring Tie Down anchors like the part # LRB1 which would get bolted to the floor of your trailer and has a 4,000 lb capacity.
I attached an install video as well. view full answer...
We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item # ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item # BP05. view full answer...
While there aren't any ratchet straps that fit directly in stake pockets of a trailer, we do have stake pocket tie-down anchors that you can use as a way to connect the ratchet straps; what you can use is the Stake Pocket Tie-Down Anchors # PK-SPTD.
Then for ratchet straps you can use something like the Bulldog Winch 13-Piece Ratcheting Vehicle Tie-Down Strap Set - 3,335 lbs # BDW20350. view full answer...
When it comes to installing tie down anchors on your 1997 Ford F-250 I recommend The Erickson Stake Pocket Tie-Down Anchors - Chrome-Plated Steel - 2,000 pounds - Qty 2 # EM09085 will work with your vehicle.
These tie down anchors have 3 different mounting holes and angles, and have a chrome-plated steel construction that resists corrosion and complements your truck's trim. This comes with 2 tie down anchors.
I attached a review video link below. view full answer...
Hi Daniel,
A steel backing plate is recommended for the surface mount Brophy D-Ring Tie Down Anchor # LRB1. We don't have one specifically for this so you'll have to find it locally at a hardware store, or we have options that do come with backing plates, the Brophy D-Ring Tie-Down Anchor with Backing Plate # DR1S or recessed Brophy D-Ring Tie Down Anchor with Backing Plate # RR5K. view full answer...
There are several tie-down anchors available for stake pockets, but the Erickson Hide-A-Hook Truck or Trailer Anchor (2 Pack) - 1,200 lbs # EM09094 that you were looking at will not fit stake pockets.
If you have the standard 2" x 4" stake pockets then you could go with Stake Pocket Tie-Down Anchors - Black Powder Coat - 2-3/4" D-Ring - 4,000 lbs - Qty 2 # PK-SPTD or Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs # T55B. The # PK-SPTD measures 5" tall and has... view full answer...
A j-hook style tie down like the part # EM78627-MS would work great with the Extang CargoCleats Truck Bed Tie-Down Anchors # EX1932 you referenced. view full answer...
The Erickson Retractable Tie-Down Anchors, part # EM01003, are a fit for your 2016 Ram 3500 truck.
The package includes 2 tie-down anchors and they have a weight capacity of 1,000-lbs.
If you are looking for tie-down straps that will work with these anchors I recommend the Ratchet Tie-Down with Clamps and S-Hooks, part # EM31352. There are 4 1-inch x 10-ft straps included and they have a weight capacity of 500-lbs. view full answer...
Each of the anchors in the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets - Flush Fit - 1,000 lbs - Qty 4, part # BU22FR, are rated for 1,000 lbs. Please keep in mind these are not the anchors compatible with your 2019 Chevrolet Silverado 2500. The Bull-Ring Tie-Down Anchors for your vehicle are part # BU23FR. They are also rated 1,000 lbs per tie-down.
I have included a product description link below. view full answer...
Go To Results