I do have suspension enhancement options for a 2002 Workhorse P42 Chassis but there are no air bags available unfortunately. Instead, you can use the Timbren Rear Suspension Enhancement System. The correct one will be based off the suspension. The part # TGMRP30MH is for models with bump stop over u-bolt pad and part # TGMRP30 is for models with bump stop on the frame. These options all work well to provide additional support. view full answer...
I reached out to the manufacturer who told me the Kwikee Series 25 Steps # LC365837 you are looking to replace your older steps with will not work. This is what they told me:
"Per my parts department, based on the information you have provided, they can verify that the customer is replacing a Series 23 Kwikee step assembly with a series 25 Kwikee step assembly. He needs to be advised not to do this, as they will not fit or bolt up properly. The frame sizes are different from one another... view full answer...
For your 1998 Workhorse P30 with a factory stabilizer the Roadmaster Reflex Steering Stabilizer # RM-RSSCP30 is a confirmed fit and is designed to replace the factory dampener and use the factory hardware of your RV. view full answer...
Yes, if you're currently using the Air Lift 1000 Air Helper Springs for Coil Springs # AL81560 you can remove those when you install the SuperCoils Custom Suspension Coils # SSC-11 on the front of your 2000 Workhorse P32 Chassis. view full answer...
There isn't a brake controller port that I am aware of on your motorhome built on a 2004 Workhorse W22 chassis, but you can check up under the dash for a bundle of wires; they would have a white tag on them. It would generally be to the far left side under the dash if they are there.
If those wires are there you would be able to simply splice in the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.
If that bundle of wires is not there you will need the Wiring Kit for 2, 4, 6, and... view full answer...
The direct replacement step for your 2005 Holiday Rambler P Series Workhorse would be Replacement Steps, Motor, and Switch for Kwikee RV Electric Steps Item # LC3722617. view full answer...
I'm glad you asked as that info is confusing for sure. I reached out to my tech contact at Roadmaster and the only thing available for your gasoline model W22 chassis is the Roadmaster TruTrac Front-Axle Trac Rod for Large Trucks and RVs # RM-TRACW-22 which essentially just holds the front axle in place to prevent jarring and unnecessary shifting. They don't have anything for the rear of the vehicle.
They do have a steering stabilizer to prevent fatigue at the wheel and help you stay... view full answer...
The Timbren front kit part # TWFRW22 that fits your 2005 Workhorse W22 is much stiffer than the # SSF-280-47 you have now. If stiffer and more supportive is what you want this would be the way to go. If you are wanting a softer ride though this is probably not going to be it. view full answer...
The Roadmaster Reflex steering stabilizer that fits the 2007 Workhorse W22 chassis is actually # RM-RBK13-RSSA. The one that you referenced, # RM-RBK14-RSSA, is for Freightliner chassis.
The steering stabilizers will come with the mounting brackets and hardware. Current pricing is available on each product page. view full answer...
The steering stabilizer that you need is Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Motor Homes part # RM-RBK3-RSSP30 for the 1996 Winnebago Brave. This steering Stabilizer fits Winnebago Brave model years 1981-1999. The Steering Stabilizer part # RM-RSSCP30 that you referenced is a fit for various other motor homes but does not fit the Winnebagos. view full answer...
I checked with Roadmaster and the correct Roadmaster Exact Center Steering Stabilizer for a 2002 Workhorse W-22 Chassis is part # RM32RR for GVWR's over 22K or part # RM88RR for GVWR's under 22K. view full answer...
According to my research the Roadmaster Rear Anti-Sway Bar part # RM-1259-109 will install on the 2004 Newmar Scottsdale that is on a 2003 W-22 Workhorse chassis. The Newmar Scottsdale from my research is 33-1/2 ft so according to Roadmaster you will not have any issues installing the sway bar. If the motor home was shorter than 33 ft the sway bar would not fit properly and you would need part # RM-1259-108.
The metal box in the photo does not interfere with the installation location... view full answer...
We do have a number of suspension enhancement options that are going to fit your 2004 Gulf Stream Sun Voyager 8368MXG built on a Workhorse W-22 chassis, but there isn't a SuperSprings Stabilizer and Sway Control Kit for this motorhome.
The best option for sway control for your motorhome is a rear anti-sway bar because they are better constructed with higher-strength, thicker steel than OEM sway bars. This means the bars are stronger with much higher roll stiffness to combat sway, and their... view full answer...
According to the owner's manual for the 2022 Honda CRV a 2WD model can be dolly towed with the front two wheels up on the dolly. The Roadmaster Tow Dolly with Electric Brakes - 4,250lbs # RM-2050-1 has sliding ramps that can fit a tread width of 34" to 77", so it will easily accommodate your 63" track width.
Because this dolly has electric brakes it does require that your motorhome has an electric brake controller. If you don't have one let me know and I can help find the correct parts... view full answer...
For a 2006 Workhorse W22 Series chassis you'll need the Roadmaster Front Anti-Sway Bar # RM-1259-105 and the Roadmaster Rear Anti-Sway Bar # RM-1259-108. view full answer...
The thicker the diameter of the anti-sway bar the better it's going to preform. The Roadmaster Rear Anti-Sway Bar # RM-1259-108 has a 1-1/2" bar diameter and the Roadmaster Rear Anti-Sway Bar # RM-1259-109 has a 1-3/4" bar diameter.
This means that the # RM-1259-109 is going to be slightly better at minimizing the sway and body roll you feel when traveling on the highway or when making tight turns.
Note: If your 2003 Itasca Winnebago Suncruiser has Firestone Ride-Rite air bags then... view full answer...
I have a great solution for you that will not require you to lift your food truck. I recommend the Timbren Rear Suspension Enhancement System item # TWRW22.These hollow rubber springs have an 8,600 lbs capacity and sit above the rear axle to help stabilize and level your food truck. They work independently from side-to-side to minimize sway and help compensate for off-center loads. We have had other customers, with food trucks, use these successful and write us back.
We also have a set... view full answer...
Roadmaster steering stabilizer # RM-RSSCP30 fits both the 2000 Workhorse P30 and P32 chassis! It is intended for models that came with an OEM dampener.
If yours does not have an OEM dampener you would use # RM-RBK3-RSSP30 and it also fits both the P30 and P32 chassis. view full answer...
The bottom portion of the SnapPad Jack Pads # SP54FR2 are approximately 1" thick but they are not meant to lift your wheels off the ground. If your wheels came off the ground that would mean you're putting the full weight of your RV onto the jacks, which is not recommend. These pads are meant to be installed on your jack feet to eliminate the need to crawl under your motorhome to position plastic pads or wood blocks. It also increases the surface area of your leveling jack's feet to provide... view full answer...
The Air Lift LoadLifter 5000 Ultimate Air Helper Springs # AL88101 are confirmed to fit the front of your 2003 Dolphin with the Workhorse W22 chassis. These have the internal jounce bumpers that will help to reduce bouncing and reduce the risk of damage to the bags in the event they become under inflated.
We also have the matching Air Springs # AL88202 for the rear suspension. These also have the internal jounce bumpers.
I recommend using the Air Lift WirelessAIR Compressor System #... view full answer...
Go To Results