the cargo mat # WT40360 for the 2008 Mitsubishi Outlander is designed to fit just the cargo area of the vehicle not including the area with the seat folded down.
For a cargo mat that will fit from the 2nd row back (fits over 3rd row when folded down) we have the Covercraft area mat # CC76207625. view full answer...
Thank you for the photo of your older Yakima hitch bike rack for which you want to confirm the fit of replacement shank/tongue assembly # 8880580.
Yakima confirmed the fit of this part on your rack. You may also need Hitch Bolt # 8890200 to secure the shank to your hitch.
I also went to our warehouse and took a number of measurements that should give you what you need to verify that this part will work on your rack. The linked photo indicates the hole diameters, hole spacing and inside... view full answer...
The correct trailer hitch for a 2019 Mitsubishi Outlander PHEV SEL is the Curt Trailer Hitch Receiver part # C13398 which is a direct bolt-on fit. The Curt hitch also has a hidden design so only the receiver tube will be present once installed which makes for the best install look. view full answer...
That is correct. In our roof rack fit guide for your 2019 Mitsubishi Outlander you will choose the category "with no existing rails or crossbars" which I've linked for you to filter through.
I recommend checking out one of the Rhino-Rack aero-style roof rack system. We have the ROC25 which has more of an OEM look as well as the Vortex crossbar system which has the overhang past each leg. Below is a list of the parts you'll need for either setup:
ROC25
Kit - # RR65GR
Vortex Aero
54" Crossbars... view full answer...
For your 2023 Mitsubishi Outlander PHEV you will need the Curt Trailer Hitch Receiver # C86FV. This has a different mounting bracket on the passenger side of the frame than the Receiver # C87WR you found which does not fit the PHEV.
I recommend installing the T-One Vehicle Wiring Harness # TK46VR when you install the receiver. This will give you a 4-way flat connector for connecting to most small trailers you might pull as well as Auxiliary Lights # C53201. The auxiliary lights are needed... view full answer...
Yes, the Curt Trailer Hitch Receiver 13566 # C86FV and the T-One Vehicle Wiring Harness # TK46VR are the correct parts to fit your 2023 Mitsubishi Outlander PHEV. I have linked the installation instructions for both of these below if this is something you wish to install yourself. view full answer...
I believe you are referring to the top rubber cover of your Thule AeroBlade crossbars and for that we the Replacement Cover Strip with Pattern for Thule AeroBlade Edge Cross Bars - 59" Long # TH69JH.
These fit the 7501, 7501B, 7502, 7502B, 7503, 7503B, 7504, 7504B, 7601, 7601B, 7602, 7602B, 7603, 7603B, 7604, and 7604B crossbars. view full answer...
I do have an option for you but there is really no reason to use the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector part # C59236 on a 2022 Mitsubishi Outlander as there is a custom kit available, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # C43WR. The custom kit simply plugs in so there is no splice or warranty issues to worry about.
That said, the connections that come with the universal harness can be sourced locally, you'd... view full answer...
As the 2023 Mitsubishi Outlander is unchanged from the 2022 you will be able to use the Curt Trailer Hitch Receiver # C87WR.
The T-One Vehicle Wiring Harness # TK46VR will provide you a 4-way flat connector. This is the wiring commonly used on most small trailers. It can also be used for Auxiliary Lights # C53201 in the event your hitch mounted accessory impairs the view of your tail lights. view full answer...
The only wiring that we know will work with your 2023 Mitsubishi Outlander PHEV at this point in time is the Curt Upgraded Circuit Protected Powered Tail Light Converter # C59496 and the ZCI Wiring Kit # 119250KIT.
The Curt wiring splices into your factory wiring while the ZCI uses clamps to sense when to send power back to the trailer lights. Both wiring kits are designed to be used with 12V power so that's what you'll need to connect the black wire to on your Outlander. view full answer...
To install 7-way trailer wiring on your 2019 Mitsubishi Outlander you'd need the part # C59496 that you referenced as well the part # ETBC7 which comes everything needed to convert it to a 7-way plus everything needed to install a brake controller and have the 12 volt accessory circuit active as well. This also gives a 4-way you can use as well. It gives option to have reverse light circuit wired in too in the future if you'd like also.
Then for a brake controller the part # TK63VR would... view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13163 excludes the PHEV. However, there is a 2018 Mitsubishi Outlander PHEV fit and it is # C13398. This will work well for bike racks and other accessories.
If you will be towing, I recommend the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT that will not require any splicing into your vehicle wiring. The zero contact interface sensors will work well to... view full answer...
Your current wheel and tire size has an overall diameter of 18.1 inches. The size you are looking at, 5.30-12, has a diameter of 21.9 inches. If you have the room for the additional tire size and you get the correct wheel bolt pattern then what you are looking to do should work well.
The taller tire should smooth out the ride a bit.
The Kenda 5.30-12 Wheel and Tire # AM30700 that you referenced has a bolt pattern of 4 on 4. If you are unsure of the bolt pattern of your current wheels... view full answer...
The Curt Trailer Hitch Receiver # C87WR will fit all trim levels of the 2022 Mitsubishi Outlander. Since The Outlander Sport and Outlander PHEV are different models this receiver will not work on those vehicles.
The Curt Trailer Hitch Receiver # C13398 is the last hitch we have confirmed to fit the Outlander PHEV and it fits the 2018-2020 model years.
The Curt Trailer Hitch Receiver # C13079 is the last hitch we have confirmed to fit the Outlander Sport. It fits the 2011-2021 model years. view full answer...
Your pictures did attach and it does look like you do have the right connectors on your 2011 Mitsubishi Outlander for trailer wiring harness # 118518 or # C56102. I have linked installation instructions and a video showing installation on a 2007 model which will be the same as your 2011. view full answer...
The fit kit you need to attach your 460 Thule Podium feet to the flush mounted rails of your 2018 Mitsubishi Outlander is the 4030, but it has unfortunately been discontinued so the only two options you have are to get some secondhand or buy a new roof rack system.
If you can't find a kit secondhand and would prefer to get a new square bar style roof rack then I recommend the 2018 Mitsubishi Outlander Roof Rack by Rhino Rack which includes the following:
Rhino-Rack 2500 Roof Rack -... view full answer...
You made really good choices with the T-One Vehicle Wiring Harness # 118482 and Curt Trailer Hitch Receiver # C13163 and I can help you along with the installation of the harness (I also added a link to a video install of the hitch on an Outlander for you to take a look at).
I have added a link to the installation instructions of the harness for you, but in general it is not an overly complicated installation. You will need to remove some trim panels at the rear cargo area in order to... view full answer...
The Curt Trailer Hitch Receiver part # C87WR is a confirmed fit for a 2023 Mitsubishi Outlander SE AWD. This is an excellent bolt-on option that provides you with a class III capacity and 2" opening which is good for use with bike racks and cargo carriers or towing if needed. It features a simple bolt-on install.
Please note, if you are towing you'll also need a few other items like the T-One Vehicle Wiring Harness part # TK46VR and Curt Towing Starter Kit part # C45534. view full answer...
Yes the fit kit part # THKIT3128 does fit your 2019 Mitsubishi Outlander and the Thule Rapid Traverse feet you have which are actually now discontinued. view full answer...
You will need the Curt Trailer Hitch Receiver # C87WR for your 2023 Mitsubishi Outlander. This receiver is custom fit for your Outlander and requires no drilling for installation. It will bolt in place on your frame using factory holes.
The Curt Powered Tail Light Converter # C59236 will allow you to add a 4-way wiring harness. This will operate the tail lights on most small trailers you may tow. It will also allow for Auxiliary Lights # C53201 if you are using a hitch mounted accessory... view full answer...
Go To Results