The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the # 8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the # LC66WD, or for self-adjusting brakes # K23-478-479. view full answer...
I am not 100% sure what you are asking. The newer models of the power centers/converter sections like the Progressive Dynamics 4500 Series RV Converter # PD4590K18LS8 are coming with the switch that you are referencing that allows you to switch between battery types for charging.
Older models do not have that switch and there are some converter sections that do not have the switch still. Since you have the 90 amp version of the 4500 series, we do not have a replacement converter section... view full answer...
If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System # LC736514-ELKIT then you'll need part # LC182492. The flat bracket can be swapped out with part # LC182494 and the swing brackets can be replaced with part # LC182496. view full answer...
For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part # LC62ED and the correct replacement drive arm (one with the motor) is the part # LC22ED. view full answer...
For your Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter - Lippert 1621 and 0719 - 20,000 lbs # RP94720 you will need the Air System Service Kit for Reese Goose Box 5th Wheel to Gooseneck Air Ride Coupler Adapter # RP86007 which will replace your damaged air line.
You can view the most up-to-date price by clicking on the link for the products which will take you to the product page.
I included a video of the # RP86007 for you to take a look at. view full answer...
The correct replacement cover for your Ventline Northern Breeze VB0568 Roof Vent is the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BV0554-01 for white, or # BV0554-03 for smoke.
I have attached a couple of videos for you to check out as well. view full answer...
I have a solution for you, but my contact over at Lippert tells me that you won't be able to replace just those casings on Solera Slide-Out Topper. The parts you need are the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning - Black # LC87FR and the Replacement Drive Head and Roll Tube for Solera RV Slide-Out Awning - Black # LC34FR. You will want to re-use the hex rods, but you will need to replace the entire roller tube assembly to get the "arms" that are broken on your... view full answer...
The correct manual override cover for your 3,500lb electric Ram jack is the Replacement Manual Override Cap for etrailer A-Frame Electric Jack # EJ-3520-BCP.
For a cover you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944026. This 14-1/2" x 17-1/2" weatherproof cover slips easily over your electric tongue jack and secures with a drawstring to helps to protect your jack motor from the elements. view full answer...
For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K # K23-478-479 or the manual adjust # K23-462-463-00 along with spoon adjuster # W80630.
The grease seal you want is AL-KO part 568861 which is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" # RG06-050 for a set of 2 seals. view full answer...
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I can be sure to recommend the correct parts. view full answer...
That is not normal wear for the L-Brackets on your Blue 2-Point # BLU75FR to be that worn. It looks like you have too much angle in the head, so I recommend trying to tilt the L-brackets a little to try and get the bar less on just that one edge, and verify your system is rated correctly for your trailer.
The tilting of the head is used to add tension to the spring bars so it's possible your spring bars are underrated for the tongue weight your using it for.
With all of that said for... view full answer...
For your companion hitch the replacement pivot arms are now only available with the base which for your model 3000 is # BWRVB3500. I'm not sure what u-bolts you are referring to, so I assume it is the chains and that is part # BW1900-2-1600. If you are looking for the saddle pin, that is # BW3025-119A. view full answer...
The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part # BK2-100 or just the Grease Seal part # RG06-050. view full answer...
I do have an option for you but Atwood was bought out and their replacement parts are no longer available, including the repair kit you would need. The best option is to replace that A-frame coupler with a new one that attaches to a 2 inch hitch ball.
I recommend replacing your coupler with the A-Frame Trailer Coupler - Yoke Latch # CA-5210-B which is the same style of coupler that you have now. view full answer...
We have replacement pitch arms for the Solera 69 inch awning setups like what you have with the part # LC375994 which would be all that you'd need. view full answer...
I have a great choice for you. While we do not carry the Dometic line of A/C's and I had a hard time finding the specifics of your 57915.731, we do have A/C's that will work to replace a Dometic A/C. There are two different routes that you can take here for replacement. A complete replacement (inside and rooftop components) or rooftop unit only (works with the inside components already in place from your Dometic).
I recommend the Furrion Chill A/C. I like these because they are some of... view full answer...
We have just what you need.
If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item Number. You would enter part # C11474.
Next, select Curt from the Manufacturer drop down menu. Then select the quantity of hardware kits you need and add to the cart and you will be good to go. view full answer...
Your Raptor Toy Hauler likely has a landing gear setup similar to the one you were looking at: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs # LC333964. If so, then the correct replacement motor would be Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 which is rated for 5,000lbs, or you could go with Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308 which is rated for 6,500lbs. This is the heaviest duty motor we have for... view full answer...
Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the leaf springs and and other information I'm sure you have 3,500 lb axles. Your standard diameter for this capacity would be 2-3/8". In addition to the capacity you want the eye to eye length to match, so we are looking at 25-1/4" long leaf springs.
I... view full answer...
We do have the Replacement Pull Pin Kit # F500136 which is the part number 18 in the photo you found. We do not carry the part number 4 for the Fulton F2 Trailer Jack # F1413040134 at this time so you may need to replace the parts from another damaged jack if your part is not repairable. view full answer...
Go To Results