Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item # LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing cutout.
To swap out a Dometic AC with one of the new Furrion Chill Cube units, you'll have to swap out your air distribution box because anything made before 2025 isn't compatible anymore due to the new R32 refrigerant. Since you have a ducted system you will... view full answer...
Hey Chris,
Our Fitguide can be a bit confusing sometimes. Essentially the whole category is broken down into whether they fit diesel or non-diesel models. Since the EcoHitch Hidden Front Mount Trailer Hitch Receiver # EH37FR fits both gas and diesel models it has both listings attached to it. You would be able to install this hitch on your 2024 Ram 3500 DRW Diesel.
If you plan on hauling some heavy items or using a snow plow then I recommend also installing some front end suspension... view full answer...
Hey Sean, if the Draw Tite hitch you have is the # 76128 it's not supposed to fit the hybrid models so that would be why you are having the problem you mentioned. The Draw Tite part # DT79MR is instead the one that fits the hybrid models. view full answer...
Hey Scott, thanks for reaching out!
Yes, the Curt Trailer Hitch Receiver # C13397 will fit perfectly fine on your 2025 Honda CR-V Hybrid Sport.
What are you planning on using the hitch receiver for? view full answer...
Hey Don! Although both fit the 2024 Ford F-350 it is a little more specific. The EcoHitch Hidden Front Mount Trailer Hitch # EH54QR is only designed to fit the F-350 dually while the # EH39CR fits the single rear wheel F-350. Neither will fit if you have the front mounted auxiliary cooler.
What do you plan on using the front hitch for? view full answer...
Hi Rusty; the Dexter # 84546UC3-EZ and etrailer # AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern on an etrailer hub and drum assembly you need the # AKHD-545-35-EZ-K. I'm sure you're also wondering about the price difference. The Dexter name generally carries a higher price while the etrailer hub is our house brand so we are able to keep the... view full answer...
Hey Arvon, I checked with Curt and the hitch part # C72ZJ that you referenced fits all models of the 2024 Lincoln Nautilus so it fits yours that has the Jet Package trim and rear kick sensors. view full answer...
Great question, Tex!
You are correct that both the Curt # C92WR and Draw-Tite # 76194 trailer hitch receivers have the same basic design for your 2024 Volvo XC60 Recharge. We actually had the opportunity to install the Curt on a 2024 XC60 so if your XC60 Recharge has the same cutout in the bumper that we show in the video (and I've attached in a photo) then you won't have to trim anything or hammer anything into place.
If the rear bumper on your XC60 Recharge doesn't have the cutout then... view full answer...
Brett, the Curt Trailer Hitch Receiver # C94RV fits all models of the 2025 Toyota Camry so it will fit both the FWD and AWD models. view full answer...
Hi John; even though they use the same frame there is some kind of difference between the two that won't allow the # C63ZV to fit the 2024 Prologue. Curt is working on a hitch for the Prologue which is the # C89RV. We have it up for pre-order but it is not yet available. I guarantee if the Blazer EV hitch fit the Prologue Curt would not be designing a different hitch specifically for the Prologue. view full answer...
Hey Ronnie,
The crossbeam of the slider base on the B&W Patriot 5th Wheel Trailer Hitch w/ Slider # BWRVK3270 unfortunately sits too low and fights for the same space as the handles/side mounting plates of the Curt Rail Adapter # C88KR (16027) so they would not be compatible together. The Patriot slider unfortunately isn't compatible with any puck-to-rail adapter on the market currently.
You would need to switch to the Companion OEM # BWRVK3775 which would have the correct mounting points... view full answer...
If you can send me the diameter of the spindle where the grease seal sits and the diameter of the hub where the seal is pressed onto I can verify if we have the correct seal.
Currently I do see we carry 2 hubs which use the Inner Bearing # LM67048 and Outer Bearing # LM11949. First is the Dexter Trailer Idler Hub Assembly for 2,500-lb Axles # DX22XR which uses the Seal # 168233. This seal has an inner diameter of 1.688" and outer diameter of 2.332". The other hub is an Agricultural Hub... view full answer...
Hey Mark, officially I have to recommend you do not use a vertical bike rack with the Curt hitch part # C33MJ even though you said you'd be at only about half it's tongue weight capacity. The issue is the vertical racks put quite a bit more leverage on the hitch since they hold the bikes so high.
For what it's worth the Draw Tite hitch part # DT67YR that fits your CX-50 does not have this same exclusion so it could be used instead. view full answer...
Hey Peyton,
Yes, those things are all indeed compatible as the crossmember won't come into contact with the over/under kit. As for the correct kit, that depends on the size of your Keystone Cougar's axles. For 2-3/8" diameter axles use the Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00; for 3" diameter axles use the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00.
Then you can use the SumoSprings but you need to have between 5-5/16" and 6-1/2" of clearance... view full answer...
Hey Mike, so I checked with Curt and their hitch part number 13630 which is our part number # C33MJ does fit the 2025 Mazda CX-50 hybrid. Curt says this actually fits all models of the vehicle actually. What are you planning on using the hitch for? view full answer...
Hey Jared,
If your axle has a brake flange like I have pictured below then you would be able to mount a 3,500lb brake assembly # AKEBRK-35 (manual-adjust) or # AKEBRK-35-SA (self-adjust). You'll also need to replace your idler hubs with drums so we'll need to know what bearings and grease seals fit your spindle. If you can't read the part numbers on them anymore then you can measure your spindle with a caliper # PTW80157 at points B, C, and D from the diagram below and I can find a compatible... view full answer...
Thanks for reaching out, George!
The PullRite SuperGlide # PUL28RR for your 2025 Ram 3500 will require an adapter to fit with different pin boxes. This is just so the pin box will be locked into position with the head so the autoslide feature works correctly.
For example, the Quick Connect Capture Plate # PUL46RR Lippert 1621/1116/1716 Pin Boxes will only fit with those pins boxes. PullRite has a variety of capture plates though so if you can let me know what you have for a pin box I'd... view full answer...
Hey Jordan,
Yep, I went ahead and verified directly with Timbren the Timbren Suspension Enhancement System - Severe Service # TGMRTT35D are indeed a fit for your 2025 Chevy Silverado 2500 ZR2.
That said, the Severe Service kit is designed for trucks that have in-bed campers or are used as work vehicles (like salt spreaders, etc.). So if you have an in-bed camper you keep on this will be great, but if you want the suspension upgrade for things like helping stay level while towing a trailer,... view full answer...
Hey Le, thanks for reaching out!
The etrailer # e67MV and Curt # C26VV hitches that fit your 2025 Lexus TX 500h Sport will likely get in the way of the kick sensor. You won't need to disable it, but you might need to kick with a back-and-forth motion instead of a swiping motion in order to get them to pick up the movement of your foot.
We've gotten mixed reviews on whether or not the kick sensor will actually still work with a hitch installed, but you at least know you won't need to disable... view full answer...
Hey Todd!
At the lowest setting, the saddle of the Power Mountain Tallboy Off-Road Bottle Jack # PM34FR sits at 14" and the top of the saddle arms are at 15-3/8". I took a photo of it out in our warehouse, and while I wasn't able to get an exact photo at eye level (my camera kept getting out of focus), I took one close to eye level so you can get an idea of the height.
If the saddle sides are too tall, you might be able to slide the bottle jack under your axle at an angle to get it in... view full answer...
Go To Results