Yes, the Curt T-Connector # 56407 will require you to route a power wire from the black module box to the battery on your 2024 Jeep Wrangler.
I know it isn't convenient, but it's the best setup when it comes to a trailer wiring harness since this tees in behind your tail lights and then powers your trailer lights via the battery in your Jeep. The separate 12V power wire powers your trailer lights but also doubles as a way to protect the OEM wiring on your Jeep. view full answer...
The High Pointe Over the Range RV Convection Microwave # HP94ZR can be vented outside but you'd need to pick up a bit of ducting and duct tape from your local hardware store to connect the vents on the top of the unit to an exterior vent. If you don't already have an exterior vent then we currently offer one in white # V2111-13 and black # V2111-55.
You'll want to pick up some butyl tape # AL28FJ and some non-sag sealant # 344270341437-1 for a waterproof connection to the trailer wall. view full answer...
Yes, the Curt hitch part # C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch. view full answer...
Looking at the wiring schematic on the unit, it looks like the red would get connected to a 12v power source, the black wire would be grounded, and the brown/white wire would need to be connected to the furnace thermostat.
For the 2 wires with the small connectors, that would be need to be connected to a heat pump. view full answer...
You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller # C24VV.
The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under your dash. Screws are also included and you can use them with the adhesive to mount the bracket under your dash. Then you'll simply slide in the TriFlex NEXT controller and that's it.
This type of bracket takes up less space than the normal U-shaped... view full answer...
To change the battery mode on the Progressive Dynamics 9300 Series RV Converter Charger # PD79RR you'll need to insert the included CLAW tool into the small opening next to the battery type indicator light. Press and hold that button (using the CLAW tool) for 3 seconds until you see the light change to the color that matches your battery type (see attached from manual). view full answer...
The four wires in the picture of the 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK you referenced are coming from the wall remote # 344410TSSW12V. You'll wire the wall remote in the following manner:
White: Fan Motor +
Blue: Fan Motor -
Black: Trailer Battery -
Red: Trailer Battery + view full answer...
I've attached the installation instructions for the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V # PD64FR for you below. view full answer...
The Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V Item # PD64FR will pull DC current from your battery and convert it to AC current for when you aren't hooked up to shore or generator power. The integrated transfer switch automatically changes from inverter to shore power when you hook up at the campground so you won't have to turn your converter on and off. If you look at the attached instruction manual you'll see how to wire the inverter... view full answer...
Yes, the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners # ACRG15 is what you need for your application. This includes a new thermostat as well.
According to my research all of the wiring for your current thermostat goes directly to the relay box. Since this unit comes with a new relay box that only requires the 4 wires you won't be using your old wiring.
Attached is a wiring diagram another one of our experts has for the # ACRG15 that you can use for... view full answer...
Dexter brake assemblies like the part # 23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made.
That being said the etrailer.com brand assemblies part # AKEBRK-7-SA are also very well made too. We have sold a ton of these and gotten very positive feedback on how well they well they work and how reliable they are. If it was my money I would go with these unless you want to have the absolute nicest materials money can... view full answer...
The correct height setting is going to vary by trailer but you can get there taking some measurements.
First make sure your trailer is on level ground and then measure from the ground up to the bottom of the king pin. Then on your truck take a measurement from the ground to the truck bed floor where the hitch will sit. The difference in these two measurements will give you the hitch height so that the trailer is level.
Next take a couple measurements to see what kind of bed rail clearance... view full answer...
The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness item # HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller.
The HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes - OEM item # HS481-8067 will allow you to use a OEM brake controller to operate the trailer brakes.
If your vehicle has an aftermarket brake controller you will want item # HS381-9067. If you have a vehicle that came from the... view full answer...
It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller # C51180 you will need an almost fully functional 7 way connector; using something like the Hopkins # 37185 adapter from the answer you were looking at would work, but it doesn't come with all of the wiring you'll need so I don't recommend using that and you will need to run a power wire to your battery (not included).
Instead,... view full answer...
I do have an option for you but SuperSprings does not offer any additional spacers for the SumoSprings Trailer Helper Springs part # SS26MV. That said, we do still have spacers that will work for this, the Timbren Spacer part # A25723-90AH00 for 1" or part # TA25722-90P00. These won't be the exact same as the ones that came with this kit but they will still work well.
In regards to the carriage bolts, you'll need to source this locally from a hardware store. view full answer...
The Curt Front Hitch # C31076 will install on the front driver and passenger side frame rails. I have linked a picture showing the bolt holes on the passenger side frame rail and it will be the same for the driver's side.
I checked and the Curt # C31076 front hitch is a confirmed fit for your 2016 Toyota 4Runner Trail Edition. I have linked the installation instructions to this page for you to check out.
I have linked the front hitch to this page for your purchasing convenience. view full answer...
In order to find a local dealer for installation purposes, there is a way for you to input your location in order to find dealers close to you. That location for this information is right below the product images and videos. Underneath those images/videos, there is a question that asks, "Need help with installation? Find local installers near me." I went ahead and included a screenshot of where this is located on the product page for # ETBC7 to give you an example. The location is in the... view full answer...
Yes, the engine on your Chevrolet Equinox will need to be run at times when flat towing. The easiest way to determine what needs to be done to flat tow your Equinox is to consult your owners manual.
I went ahead and took a look at the owners manual for both the 2021 and 2022 Chevrolet Equinox. For either model year, you will need to run the vehicle at the beginning of each day and at each RV fuel stop for about 5 minutes. This will ensure proper lubrication of the transmission components.
I... view full answer...
To remove the hinge pin you'll need to remove the Phillips screw from each side of the cover. Then the lift arm supports can be disconnected from the lid, and the new lid can be put in place. You just want to make sure to replace all the hardware you removed to get the lid off.
Fortunately there's not too much involved to install the Replacement Lid for MaxxFan and MaxxFan Plus Roof Vents # MA10A40009K. You can replace it without having to remove the whole fan; only the lid needs to be... view full answer...
Go To Results