In regards to the Redarc Tow-Pro Liberty Brake Controller part # # RED24FR, the unit should not be illuminated while driving without a trailer. If you press the button while a trailer is not attached you should see a breathing blue light and that simply indicates the controller is in sleep mode. This is further explained in the manual so please give this a look over. view full answer...
Hi Keith, welcome back! It looks like you went ahead and ordered the following:
-Demco Classic Base Plate Kit - Fixed Arms # DM9518302
-Roadmaster Falcon 5250 Tow Bar Adapter Brackets for Demco Classic Base Plates # DM9523023
-Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord # RM-15267
-Roadmaster FuseMaster Fuse Bypass Switch for Towed Vehicles - (2) 20-Amp ATC/ATO Fuses # RM76514
-Roadmaster FuseMaster Fuse Bypass Switch for Towed Vehicles... view full answer...
Hello Shirley, thanks for reaching out. The LaSalle Bristol Double Bowl RV Kitchen Sink - 27" Long x 16" Wide # 34413TLSB27167 will drop into a 27-1/2" x 14-1/2" hole, but the overall width of the sink including the flange is only 27" so you'd end up with a small gap that would have to be filled or covered. Generally, you want the hole to be at least 3/4" smaller than the sink flange itself which is 27" x 16". view full answer...
From the information I can find I believe your 2019 GMC Acadia will have the wiring routed back towards the rear of your vehicle whether you have the factory tow package or not (see attached photo). If you check up under the rear bumper of your Acadia you should find the wiring harness that you would plug the T-One # 118720 (for a 4-Way) or # 118276 (for a 7-Way) into. I have attached some installation videos on a 2017 Acadia as well as the written instructions for you to reference. I like... view full answer...
Your 2018 GMC Acadia actually has blunt cut wires for you to splice in a brake controller like the Tekonsha Prodigy P3 # 90195. The last Acadia to use the Adapter # 3026-P that you referenced was the 2017 Limited which was the same as the 2016 model year. The 2017 New Body and newer have the blunt cut wires up under the dash.
I took a look at the online version of the owner's manual for your 2018 Acadia and on page 278 it says that the blunt cut wires can be found above the parking brake... view full answer...
Your best bet is actually the saddle mounts. Unfortunately, there's no good J-Style racks that are locking and will have the weight capacity for your kayak. Saddle mounts directly transfer the weight to the bars, so they are a lot easier for fitting heavier kayaks.
I have two saddle-style recommendations for you that include locking features and can support the weight of your kayak.
The first is the Inno Locker, part # INA446. This is a strap-down carrier that will carry the kayak hull... view full answer...
Hey Dominic. Since you have the AT4 model of the 2021 GMC Acadia you'll need the Draw-Tite Hitch item # 76023. This hitch is custom fit for your Acadia and bolts to it with included hardware. It's going to mount behind your rear bumper cover and be completely concealed when you cover it with the rear trim piece.
The Draw-Tite Hitch item # 76023 is a class III hitch with a 2" receiver. It has a 4,500 lbs towing capacity and a 675 lbs maximum tongue weight.
What do you plan on using your... view full answer...
Hello again, Joe!
If the 2025 GMC Acadia you are looking at has the factory towing package, from what I could find, there will be 4 wires wrapped up in a bunch of cables in a harness on the leftmost side of the driver's footwell. Remove the black tape and you find the 4 wires. It sounded like it was a pain to find it, so patience will be needed. I do have to admit that I couldn't find whether or not anything needed to be activated for the brake controller to function properly, so that... view full answer...
Hey Jimmy, we do have a hitch that fits your 2020 GMC Acadia AT4 with the Draw Tite part # 76023 but the Curt you mentioned excludes the AT4 models so it would not work for you. view full answer...
Vehicle manufacturers do not recommend placing any cargo directly on sunroofs. The glass was not designed to support additional weight.
A better option for you would be to add crossbars to your factory side rails and use a roof basket and a cargo bag or a roof mounted cargo box. This would keep the load off of the sunroof and allow you to carry more weight.
Based on your photo, it appears that you have a GMC Acadia. There are different roof rack options depending on the year of your... view full answer...
Hey Dennis! The Acadia and Traverse do share a lot, but the coil springs are different which means the # AL99PD will not fit your 2025 Traverse High Country. You may be able to use the universal springs like # AL60909 but you will need to measure to find the right fit.
First, unload your vehicle to make sure it's at normal ride height. Then, measure the inside height of your coil spring, which will be from the upper spring seat to the lower spring seat. Lastly, measure the inside diameter... view full answer...
Hello Ronald,
No, the SLT and AT4 are different submodels of the 2023 GMC Acadia. I can verify for you that there are running board fits for your 2023 GMC Acadia AT4, though, from Aries. I checked with the manufacturer to confirm this for you, and what you can use are either of the following
- AeroTread Running Boards w/ Custom Installation Kit - Black Stainless # AA48ZB
- AeroTread Running Boards w/ Custom Installation Kit - Polished Stainless # AA43ZB view full answer...
So the red wire of your brake controller needs to be connected to a circuit of your 2018 GMC Acadia that sees voltage only when the brakes are applied. If you used a custom install harness on your Acadia like the # 3026-P to install the controller then most likely you have a blown third brake light fuse since that's connected to the stoplight circuit for the brake controller.
If the controller was hardwired to a stoplight circuit you most likely need to check the condition of the connection... view full answer...
Hey Don! The Replacement Clevis End Kit # e54ZR is designed for the etrailer XHD. This will work with the Demco Excali-Bar III # DM9511013 with a weight capacity of 10,500 lbs but not other Demco tow bars. Do you have the Commander II # DM9511012? This is rated for 6,000 lbs and is equivalent to the etrailer SD # e74ZR. If that is the case, you need the Replacement Clevis End Kit for etrailer SD Tow Bar # e22VR. view full answer...
Hey Josh, the Equal-i-zer weight distribution system part # EQ37060ET would be a great option for your 2022 Rockwood 232 esp. Then for a set of 10 inch frame brackets like you'd need you would want the part # EQ24FR. view full answer...
Hi Robert; the Curt Front Mount Trailer Hitch # C52NR is designed to fit newer models of the Silverado and Sierra 2500/3500. At this time there are no custom front hitches available for your Acadia. If you want to use the Meyer HomePlow Residential Hydraulic Snowplow # ME53FR you will have to see if a local fabricator will make a custom fit hitch for your vehicle.
Do you have a long drive you need to clear or will you be using the plow for something else? view full answer...
The trailer hitch we offer that is designed for your 2017 Acadia is the Draw-Tite, part # 76023. This is a Class lll hitch and it has a 2-inch receiver opening. If you are mechanically inclined you should be able to install the hitch with no problem. If you are not comfortable you can have a trusted mechanic complete the installation for you. I am attaching the installation instructions in a separate email.
If you plan on doing some towing you might be interested in etrailer ball mount... view full answer...
Hey Mike. For a 5th wheel trailer that long, I recommend using two of the MORryde I-Beam Mounted Stabilizer item # MR96RV. Mounting one of these in the front a few feet back from your landing gear and then one in the back is going to take care of any swaying or rocking feeling inside your trailer.
The MORryde item # MR96RV requires exposed I-beams to mount and 12" or more inches of clearance from the bottom of the I-beam to the ground.
What year and model 5th wheel trailer do you have? view full answer...
Hello Robert, thanks for reaching out. The Andersen Weight Distribution Hitch can indeed be used with your 2025 GMC Acadia towing a 5,000 lb trailer. For that, you can use the following:
- Andersen Weight Distribution Hitch w Sway Control - 6" Drop/Rise - 14K GTW, 1.4K TW # AN53VR view full answer...
Go To Results