See what our Experts say about this Optronics Trailer Lights

• Recommended Replacement Light/Lens for an Older Reflect-O-Lite 400
  the Reflect-O-Lite 400 light has been discontinued for quite a while so there isn't going to be an exact replacement. Instead, the closest replacement lens we have is the Replacement Amber Lens for Optronics MC66 Series Clearance or Side Marker Trailer Light # A66AB or the Replacement Red Lens for Optronics MC66RB Clearance or SIde Marker Light # A66RB. Both of these lenses measure 4" long x 2" tall x 7/8" deep, and is made of acrylic. There's no guarantee it'll be compatible with your...
  view full answer...
• 2013 Forest River 2300 Sunseeker Front Amber Running Light Replacement Lenses
  I don't have any way of knowing what light is on your 2014 Forest River 2300 Sunseeker. I can confirm that the Optronics Dual Bulb Trailer Clearance and Side Marker Light - Incandescent - Oval - Amber Lens # MC66AB is 4" long x 2-1/16" tall x 1-1/16" thick with base mounting holes 3 inches on center. It is an exact replacement for Uni Bond #ML2043A, Truck Lite #26301Y, Grote #45263, Peterson #135A, and Bargman #30-58-002. The lens replacement for this is Replacement Amber Lens for Optronics...
  view full answer...
• Wiring Single Wire Clearance Lights on an Enclosed Trailer
  You will need to use a circuit tester, item # PTW2993 if needed, to test the wires exiting the trailer to figure out the wiring configuration with the trailer hooked up to the truck and the running lights on. You will probably find that you have taillight power on one of the green wires and no power on any of the other wires. In this case you would wire the two green wires to the power wire coming from the clearance light. You would then need to wire the two white wires coming from the...
  view full answer...
• Clearance Trailer Lights With Replaceable Lens Recommendation
  We do have clearance lights that may work for you. The clearance lights we offer come in amber or red and we have either 1 or 2 bulb units. You mentioned you like the 2-bulb feature on some clearance lights. I recommend part # MC66RB. This light comes with 2 incandescent bulbs and has a red lens. The amber version of this light is part # MC66AB. Both of these lights use the replacement bulbs, part # A194B. These are push-in bulbs. The replacement lens for the red light assembly is part...
  view full answer...
  
• Replacement LED Red Clearance Light For A Bargman 58-Series Clearance Light
  Hey Luis, For an LED version of the Bargman 58 series clearance light you would want the LED Trailer Clearance or Side Marker Light w/ Reflex Reflector # MCL32RB. This is a surface mount design so you'll need to pick up some self-tapping screws and I'd also recommend using some butyl tape # AL28FJ on the backside of the mounting base to help prevent any water from leaking into the wall of the trailer.
  view full answer...
• Comparing Amber Clearance Lights with 1-Wire vs. 2 Wires
  The difference between a clearance light with one wire and one with two is simply that the 1-wire type uses the light's mounting hardware to establish the ground, rather than a separate ground wire. The two are interchangeable so long as the mounting surface on the trailer will allow you to drill a hole to let you attach the white ground wire to the frame. Alternately, you could attach the ground wire to another of the existing ground wires on the trailer.
  view full answer...
• Replacement Amber Lens for Marker Light on a 32 Foot Yellowstone Camino Camper
  I wish we had a master list of the parts used on all trailers and RVs but we do not. So we have to go by measurements or part numbers on the individual parts if applicable. The amber version of lens A66RB is # A66AB. It is a replacement for light # MC66AB which is 4" long x 2-1/16" wide x 1-1/16" deep. And that light is a direct replacement for any of the lights below: Uni Bond ML2043A Truck Lite 26301Y Grote 45263 Peterson 135A Bargman 30-58-002
  view full answer...
• Replacement Lenses for Unknown Trailer Lamps
  We have a pretty large selection of replacement lenses available. I'd be happy to look at a photo of your current lenses if you'd care to send it along. You can simply attach the photo to a reply to this email. Also helpful would be any item or part numbers printed or stamped into the light fixture itself (not the lens). Any numbers on the lens itself would be DOT certifications, not a part number for the lens. Dimensions of your current lenses would be helpful as well. I've linked you...
  view full answer...
• Could Optronics Trailer Clearance Taillight # MC66AB Possibly Replace Lights that Hardware Ground
  The simple and efficient solution would be to go with the part # MC66AB that you mentioned and if you find that the lights ground through the hardware just run the white wire back to the mounting hardware and you'd be set.
  view full answer...
  
• Is railer Clearance and Side Marker Light, # MC66AB, Submersible
  The Trailer Clearance and Side Marker Light, # MC66AB, is not a submersible light. You will not want to put this light under water. A sealed light like # MCL49AB, would be the way to go. I have included a link to a video review of this light for you.
  view full answer...

Do you have a question about this Trailer Light?