Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This GloLight Halo LED combines standout looks with real performance. The outer red ring works as a tail light, the center white LEDs flash for turn signals, and both sections brighten for braking. With 21 LEDs drawing only 0.145 amps for tail lights and 0.375 amps for stop/turn at 12.8 volts, it’s far more efficient and durable than incandescent bulbs. The bright, even halo glow is easy to see day or night, so you get reliable visibility without extra power draw.
Water damage can ruin a light fast, but this one’s sealed tight. The polycarbonate housing and tinted acrylic lens are waterproof, making it great for boat trailers or any setup that sees rain, road spray, or full submersion. Once installed, you can count on it to keep moisture out and keep shining bright no matter the conditions.
Getting a snug fit is straightforward thanks to the recessed mount design. It installs in a cutout using grommet A45GB (sold separately), or you can use optional bracket BK45BB (sold separately) if you prefer not to cut into your trailer wall. The standard PL-3 connector works with a 3-prong plug like A45PB or A47PB (sold separately), so wiring is simple and secure without any guesswork.
Safety standards matter when you’re on the road. This light meets DOT, FMVSS 108, and CMVSS requirements, so it’s approved for highway use right out of the box. You get the peace of mind of a tested design backed by a lifetime warranty on the LEDs—solid performance for the long haul.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at and showing you how to install the GloLight LED trailer tail light with the clear lens.What sets this light apart from many of the others is its running light. As you can see, it has that circular halo design, and puts out a pretty good amount of light. Now, when you hit the brake lights, it really makes a difference in how bright it is, to let others know that you're applying the brakes. Same thing with the blinker. As you can tell, it's nice and bright.Another thing that separates this light from many of the others is its clear lens. In my opinion, when the light's not in use, it just gives off a little more of a clean look.
The light is going to have 21 diodes. Its power draw at 12.8 volts, to run the tail light, it's going to take .145 amps; and for your stop and turn, it's only going to use .375 amps. Now that's good, because it'll give you plenty of power to run all your other lights that you might have.This light is sonically sealed, which means it is submersible, however I don't recommend submersing it for any length of time or when you have power to the light.One thing I really like about this light is that it's LED, which that means it's going to be a lot stronger, brighter, and last a lot longer than your traditional style incandescent light, which means it'll be a great replacement or even an upgrade for it.Here on the backside of the light, you can see we have our three connection points. They are going to come covered in dielectric grease, so you don't have to worry about that during your install. Each one actually has a description of what each contact point does.I'll show you just how easy it is to get our light installed.
Just take our connector, feed it through the hole. Just plug it in. Sometimes these lights can be a really tight fit, so if you need to use some silicone spray or even some soapy water to help assist you getting it in, you can do that. Start at the top, put it in first. You'll feel it seat all the way down into the grommet.
It's just that easy. All right, now we'll go ahead and put some power to the light, and make sure it works. If you bought more than one of these lights, you go ahead and repeat the same process on the other side.That'll do it for our look at and installation of the GloLight LED trailer tail light with the clear lens.
Ratings & Reviews
Tom D.
4/2/2019
The lights are as good today as when purchased. Plus great follow-up support
Heather A.
5/15/2018
Curt, thank you for your review. This lights are not sold with the rubber grommet or pigtail. The grommet is part # A45GB and the pigtail would be part # A45PB or part # A47PB.
John M.
7/27/2015
just like a timex watch takes a licking
Derek P.
7/19/2021
Still great, nice and bright. They are a huge improvement over the factory incandescent signals.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
John
3/20/2018
Had the lights on my semi trailer for a year no problems look great ! I had a few people ask where I got them I did not hesitate to tell them !