2-1/2" Round. Low-profile LED trailer light serves as either a side marker or clearance light. Built-in reflex reflector. Snap-on polycarbonate lens. Surface mount with included gasket - hardware not included. 2-Wire design. P2 rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to take a look at the Optronics round LED clearance or side marker trailer light with the built-in reflector and the amber lens.Now this is a round trailer light that can function as either a clearance or side marker light, has a built-in reflex reflector to eliminate the need for a separate reflector, and it does use LEDs, which make great replacements for incandescent lights. They last 50 times longer, they're more efficient because they'll provide brighter light with less power output, and of course no bulbs to replace or brittle filaments to break. This is a durable polycarbonate snap-on lens on a black ABS housing. It has an amber lens over a white LED. This slide is compatible with 12 volt DC systems, and it is a surface mount design. You mount surface mount this to the trailer.Now the hardware to install, this is not included.
They do have this attached foam gasket on the back to help create a nice weather tight seal when you install it, and you can see it has a two wire pigtail, which will hard-wire into your trailer. The yellow is for the power. White is for ground. This is a P2 rated light, which would produce a 90 degree beam pattern. It is for quantity of one clearance or marker light.
The dimension on the light. The diameter of it is right at two and a half inches. Depth of it is about a half an inch. And the power draw at 12 volts is 0.073 amps, does have a lifetime warranty on the LEDs.And the last thing I want to do is hook these wires up just to show you how bright the light is. It's a real good hook on our ground up, put up the power up, turn on our 12 volt.
I know you can see the light lit up. I'll go ahead and turn off the overhead just so you can see in the dark how bright the LED will light up as a clearance or side marker light. Go ahead and turn back on our overhead light and disconnect it. But that should do it for the review on the Optronics round LED clearance or side marker trailer light with the reflex reflector.
Average Customer Rating: 4.9 out of 5 stars (17 Customer Reviews)
2-1/2" Round. Low-profile LED trailer light serves as either a side marker or clearance light. Built-in reflex reflector. Snap-on polycarbonate lens. Surface mount with included gasket - hardware not included. 2-Wire design. P2 rated.
Easy ordering quick delivery and priced right Great service always from etrailer
Another great product that E Trailer offers. Well made, compact and bright illumination.
Lost a lens on my trailer. This is the only one I could find on the internet. It is not as deep as the old one but it does fit. Geat price.
product was exactly what I needed. I was advised what was happening with my order from the get go. Great job everyone Thanks Jerry
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.