See what our Experts say about this MORryde Accessories and Parts

• Can The MORryde Storage Bracket For WDH Stay On The Trailer's A-Frame While Driving?
  That’s one of the big advantages of the MORryde WDH Storage Bracket # MR62ZV - you can leave it mounted while you’re on the road. It bolts permanently to the A-frame and won’t interfere with your hitch. Just remove the bars and shank and install on the hitch receiver when you’re ready to hit the road. No drilling is required. In some rare instances, some travelers may prefer a more temporary storage solution like the # MR72ZV. This doesn't require drilling holes into the trailer's frame...
  view full answer...
• How Do I Know Which MORryde WDH Storage Bracket To Use On Jayco Keystone Camper ?
  Hey Phil, you’ll need about 10 inches of unobstructed space on one side of your trailer's A-frame to bolt on the MORryde EzStor - Storage Bracket for WDH # MR62ZV. Then it does protrude inwards the length of your trunnion bars, so that's something to keep in mind (see attached photo). It usually clears battery trays, but if your wiring or support brackets are in that zone, send us a photo and we can help you double-check. If you don't think you have the room, you'll instead want to look...
  view full answer...
• How To Story Equalizer Hitch When Not Using It
  Yes, Greg, it’s a nice match for Equal-i-zer bars. The notched tray on the MORryde EzStor Lite Rack for WDH # MR72ZV fits standard 4-point sway bars like Equal-i-zer just fine. Just drop the bars in and they’ll rest securely until you’re ready to hook up again. What do you normally tow with the Equal-i-zer hitch?
  view full answer...
• How To Know If You Have Clearance On Trailer's A Frame For MORryde WDH Storage Brackets
  From the top of your frame to the highest point of the bracket, you’re looking at just under 5-1/2 inches. That usually clears LP tank covers, but if yours flares out low, you might need to offset it rearward slightly. The full dimensions of the MORryde EzStor - Bolt-On Storage Bracket for WDH # MR62ZV are -6-3/8" tall -22-1/4" wide -17-1/2" deep As long as you have room for this, and also a little bit more room on the inside to clear the trunnion bars as seen in the attached pics, you'll...
  view full answer...
• Will MORryde Storage Bracket For WDH Work On Tapered A Frame Trailer?
  As long as you’ve got a flat section that’s 5–6 inches long and between 2inch and 2-1/2inch wide, you’re in good shape, Janine. Just slide the MORryde Removable Storage Bracket # MR72ZV back a bit until you find a secure, flat spot to clamp it down. I haven't seen many tapered A-Frame trailers. If you have a pic or at least the trailer model and info, let me know!
  view full answer...
• What Size Weight Distribution Hitch Shank Does MORryde Removable Storage Bracket for WD Fit
  Hey Jonathan, I hope MORryde comes up with a 2-1/2 inch hitch version of the WD storage bracket part # MR72ZV that you referenced but it only will fit the shank of a 2 inch system.
  view full answer...
• Can I Leave MORryde WDH Storage Bracket On Trailer While Towing?
  Nathan, you technically can, but I’d advise against it. Since the MORryde EzStor Lite - Removable Storage Bracket for Weight Distribution Hitches # MR72ZV is not bolted through the frame, the vibrations from driving can loosen it over time. Most folks just pop it off and store it in the front compartment or under a bunk when traveling. If you'd like a more permanent bolt-on option, I'd instead go with the MORryde EzStor - Bolt-On Storage Bracket for Weight Distribution Hitches # MR62ZV. What...
  view full answer...
• How Sturdy And Secure Is MORryde No-Drill WDH Storage Bracket For Trailer A-Frames?
  Jeff, it’s more solid than you’d expect for a no-drill bracket. The # MR72ZV is sturdy and has a bit of weight, especially once the weight distribution hitch and bars are added. Nobody will be lifting that off the trailer's frame all in one go. If you wish to, you can add a 1/2" set screw to the bracket to hold it snug without shifting. Just keep in mind, it’s meant for parked use only, not for towing (even after adding set screw). For even more security, you can lock the WDH shank to...
  view full answer...
• Can MORryde WDH Storage Rack Stay On Trailer's Frame While Towing?
  Shannon, I wouldn’t recommend that. This # MR72ZV bracket isn’t bolted through the frame, it’s just held in place by the weight of the bracket. A 1/2" set screw can be added if wanting a more secure fit. It works great for storing your spring bars and wdh shank while parked, but it can shift during travel. It’s best to remove it before you hit the road. If you want a more permanent solution, Id look at the MORryde EzStor - Bolt-On Storage Bracket for WDH # MR62ZV. This doesn't need to...
  view full answer...
• No-Drill WDH Storage Rack For Rental Trailer - Jayco Jay Flight
  Alyssa, this is exactly what you want for a rental trailer. The # MR72ZV clamps on and off in just a few seconds, no tools or permanent marks. It’s a great option if you want quick storage at the campground and need something easy to remove before hitting the road. Also, I've had to remove a weight distribution shank and head out of a small storage compartment before, and it's a pain in the neck to say the least. I think you'll really like this option. Have you rented a camper and used...
  view full answer...
• Very Easy No-Drill Storage Rack For Weight Distribution Hitches On Trailer's A-Frame
  Maya, you’ll love this - it takes maybe 2 to 3 minutes, tops. You just slide the MORryde Removable Storage Bracket for Weight Distribution Hitches # MR72ZV over the trailer's A frame, and you’re done. It’s a great option if you want something hassle-free. If you really want to, you can pick up a 1/2" screw or bolt and install it on the back side to use as a set screw, which would make it more secure. But it's still recommended to remove the storage rack from the trailer before hitting...
  view full answer...
• Storing Weight Distribution Hitch On Tongue Of 2021 Forest River R-Pod Camper
  Caleb, most R-Pods have a standard 2inch wide A-frame, which is no issue for the no-drill MORryde WDH Storage Bracket # MR72ZV. It fits up to 2-1/2 inch wide frames and the height of the trailer frame won't matter at all. If you’ve got obstructions like wiring or propane lines nearby, just mount it a little farther back. I've attached a demonstration video for you to check out and see how simple the install process is (literally a few minutes). How do you like that Forest River R Pod?...
  view full answer...

Do you have a question about this Accessories and Part?