Thin factory jack feet are usually the first weak link in your camper's landing gear. When they bend or sink, these 9" steel pads swap in for the original feet, adding a wider footprint and built-in articulation for uneven ground.
If you've ever watched a factory pad start to curl at the edges while leveling, you already know the weak point. Thin stamped feet flex under load, and once they bend, the load shifts back into the jack leg itself. That's how minor deformation turns into long-term wear, alignment issues, and expensive hydraulic repairs.
These 9" pads fit standard 2" round leveling jack legs and include the pin connector for installation. Laser-cut from 1/4" plate steel and reinforced with six gussets, they're built to hold their shape when the weight comes down instead of flexing and fatiguing over time.
Campsites aren't all poured concrete. You back into what looks level, drop the jacks, and one corner always seems to settle differently. A rigid foot can force the jack to load at an angle, which adds strain where you don't want it. The integrated ankle pivots up to 10°, allowing the pad to adjust to slopes and uneven terrain. The leg stays aligned while the foot sits flatter on the ground, which helps the entire leveling system work the way it was intended. Instead of wondering if a soft site will leave you re-leveling in the morning, the jack stays aligned, the load stays distributed, and your leveling system holds its position overnight.
Soft soil, gravel pads, sandy lakeside sites, they all test small jack feet. A narrow pad concentrates weight in one spot, which can lead to sinking and shifting as the ground compresses. The 9" round footprint redistributes that weight across a wider surface area, reducing how much the pad presses into the surface below. The broader base gives the jack more support underneath, especially when the ground isn't as firm as it first looked.
It only takes one hidden curb, rock, or raised edge to put a jack system in a bind. When a rigid foot meets an immovable object, something's gotta give, and that 'something' is often your hydraulics or frame. These pads are designed to detach first, sacrificing the foot instead of forcing that shock into components that cost far more to repair.
RVpaws are designed to work with compatible SnapPad Xtra pads, combining the strength of reinforced steel with added grip and ground protection. If you'd like additional traction on concrete, gravel, or other campsite surfaces, compatible 9" round SnapPad Xtra pads (SP54FR, sold separately) install directly onto the RVpaws foot.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody, Andy here with etrailer. Let's take a quick look at these RVpaws V2 Replacement RV Foot Pads for your 2" round leveling jack legs. Now this is going to be an upgraded replacement foot pad set for your 5th wheel landing gear, specifically designed to swap out the standard 2" inch round leveling jack leg feet pads on your 5th wheel landing gear. On your screen, I'm showing you that these are gonna work with the standard 2" inch round leveling jack legs on your 5th wheels. This is also gonna be compatible with Lippert Ground Control 3.0 Landing Gears. So this is not just a simple replacement, it's gonna solve a few problems, a few common pain points that people run into when they're setting up their trailer.
One of the biggest advantages is how this is going to handle uneven ground. Each of these feet have an articulating ankle that's going to pivot up to about 10 degrees. So instead of sitting awkwardly or unevenly, this is going to adjust to match the terrain. That's gonna help keep your setup more stable right from the start. Installation's gonna be pretty straightforward since this comes with the pin connector that you need to attach to your round jack leg.
So on your screen, I'm just showing you an example of what it's gonna look when you get your leg into the included pin connector. So very easy to get these installed. These also have a much larger footprint. So getting my ruler here just to confirm the diameter, as I hope you can see, we're sitting right at 9". So that's gonna help spread out the weight a lot better.
So for instance, if you're parked on softer ground, like gravel, dirt, or grass, this is gonna be far less likely to sink in or shift over time. In terms of durability, these are built from thick 1/4" laser-cut steel. And if you also notice here, these are reinforced with gussets. So these are designed to handle heavy loads without bending. And if you accidentally hit something while maneuvering, the pad is designed to detach instead of transferring that force into your landing gear or frame.
Basically it has built-in protection. Now, if you want even more grip, or ground protection, these are compatible with the 9" SnapPad Xtra pads. Those are rubber pads that these will pop into. I think, in my opinion, that's a great addition to consider with these foot pads, that those SnapPads will give you a little bit extra grip and better protection as well. So if you're interested in taking a look at those, on your screen, I am including the part number. You can just take that part number and pop it in the search field of our website. That will take you to that pad. You can add them to your order if you so desire. Well, I think that's gonna wrap up our look today. I do hope that it was helpful for you. Again, my name's Andy. Thank you for joining me.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.