Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If your old brakes are dragging or losing stopping power, this Kodiak disc brake kit is a serious upgrade. The 13" stainless steel rotors and self-adjusting calipers deliver smooth, consistent braking even at highway speeds. With fewer moving parts than drum designs and high-performance ceramic pads, it stops stronger and runs cooler with less maintenance over time.
Saltwater and corrosion can destroy regular brake parts fast. Every piece of this kit—rotors, calipers, and mounting brackets—is made from stainless steel for complete rust protection. Rated for 1,000 hours of salt-spray resistance, it’s ideal for extended marine use and offers long-term durability no matter the environment.
Heavy braking generates heat that can warp rotors or fade pads. These vented rotors dissipate heat efficiently to prevent damage and keep braking smooth. The slip-on, over-the-hub design fits right over standard idler hubs and is held in place by your wheel bolts, making it easy to remove for service without replacing the whole hub assembly.
The included stainless steel mounting brackets use a 4-bolt brake flange configuration and feature side-support design so load is carried by the bracket—not the bolts. Extra embossing gives added thread contact for a tight, secure mount. It’s a setup built to handle real towing loads without flex or movement.
This kit fits 8,000-lb Dexter axles with #42 spindles and 16" or larger wheels using an 8 on 6-1/2" bolt pattern and 9/16" wheel bolts. With its stainless steel components and precision fitment, it’s made to deliver reliable braking performance season after season—and it’s backed by a 6-year warranty for peace of mind.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're going to be taking a look at the Kodiak line of Disc Brake Kits. Now, these kits are available in multiple configurations to fit multiple size axles. They're also available in several different finishes.A disc brake kit like this one from Kodiak is an excellent solution to give us good braking force. Typically, for this kit anyway, you're looking at like a 3500-pound axle. A lot of boat applications, you're hauling a boat sometimes miles and miles and miles, and without brakes on your trailer, you put a lot of unnecessary stress and strain on your truck. A braking kit like this allows us to take the stress, the strain off the braking system on our truck but also gives us a safer ride.In this application we've got a surge coupler at the front of the trailer, so as the truck slows it applies the hydraulic fluid pressure, squeezing our caliper together giving us excellent stopping abilities.
The rotors, calipers, and the ceramic pads are all automotive grade, so they're going to be made to the highest standards being sure we get excellent braking capabilities.Now when we compare a disc brake kit like this to a hydraulic drum-style brake, there are several advantages. Of course, we all know disc brakes tend to work better than drum brakes. They lock up less. We typically don't have the moisture being held inside. Especially in a marine application, that hub fills up with water, that moisture stays inside, causes some corrosion issues.
In this situation, once we bring these out of the water, everything's going to drain away. Air can get to it very readily and dry everything up.Another advantage we're going to get with this particular kit over the other disc brake kits available, the material composition is very corrosion-resistant. Our rotor, caliper, all stainless steel, plus they take that a step further, put a Dacramet finish all the way around. So that's going to work out really well, especially in a marine application like this, but also just on a utility trailer, keeping everything nice, corrosion-free. It's also going to be an excellent, excellent choice if you use it in a saltwater-type application.Something else you'll notice, pretty common on automobile applications, not usually on trailers, is going to be the ventilated rotor here.
So you've got two wear surfaces here and here. Those are going to be separated to allow air to flow freely in there and get everything cooled off to give us premium braking performance every time we hit those brakes.All right. With the bracket installed, we can move onto installing our rotor. That's one of the big benefits I like about this kit. You don't have the whole disc with the hub assembly in it.
So if you ever need to replace the disc, you're just replacing the disc, not your entire hub. This is going to fit right on our idler hub just like that, very common on automobile applications. They call this more like a top hat rotor where it it slides over your lugs, and then your wheel is actually going to hold that in and flush.Next, we'll move on to getting our caliper installed. Now the calipers can go either side. You don't have to have a left and a right. You can see we've got a bleeder screw on both sides. We want, of course, for our hydraulic connection to be facing in. Our slide bolts are going to come in this way just like that, and then these two portions are going to go on the back side of our bracket. So we slide that over, bring it in, and then we'll just push our bolts in, line them up with our holes and get them started. Now those do have loctite on them, so you'll just get them started a little bit, and then we'll use a 13mm socket and snug them on down.Now that we've got those snugged down, we'll use our torque wrench and we're going to torque them down to the specifications listed in the instructions. With our brake assemblies in place, it's time at this point to install our tire back on. Now, we do recommend using a torque wrench and torquing these down properly per the 1/2" stud application. Something we've seen, especially in the automobile industry, if you tighten these lug nuts down too much, you might cause that rotor to warp a little, decreasing your performance. That's going to complete our look at the Kodiak line of Disc Brake Kits.
Ratings & Reviews

Michael
8/31/2024
Still working great and looking good.

Gregory
3/28/2025
These Kodiak SS brakes are working fabulous. The boat trailer they are installed on is used in salt water only and they still look like new and function like new.


Victoria H.
4/11/2025
Thanks for the great feedback Ryan! Glad the kit was a perfect upgrade, and we appreciate you sharing the bolt specs, that is super helpful for others. I'll let Jacob know you gave him a shout out!

Gwendolyn Y.
3/10/2025
Hey Lee! I'm glad to hear everything is working so well! When do you get to launch your boat for the season?

Robert J.
7/10/2023
No signs of corrosion - good. Even though I am a tight wad, I just bought and installed a second set of Kodiak SS brakes on another trailer axle. The disc brake pad backing plates on this set are SS which is a big deal

Jbuilt
1/25/2021
Well after about a year on the the boat trailer all is well. It gets used on long and short trips and dunked in salt water. I’ve had it serviced to see how it looks inside and due to the fact that the Kodak hub is stainless steel there’s been no rust show up to destroy the bearings or damage the shaft spindle either. I’d recommend it to have a longer life system. BTW I have two braked axels that are all Kodiak brake and wheel components on them. In addition I chose to put electric over hydraulic on the trailer and I’m also happy with that too.

Dwight
3/7/2025
working well

Do you have a question about this Trailer Brake?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Kate F.
12/3/2025
Glad you make the switch to disc brakes Todd, and went for the stainless especially since you are launching into salt water. What body of water are you mainly going out in? We are located in Missouri so I am out on the Lake of the Ozarks and Mark Twain Lake when I can. I dabble in some local bass tournaments as well.