To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Most roll-up covers trade strength for flexibility, but this one doesn’t. The TruXedo Sentry uses heavy-duty 3/4" thick aluminum slats bonded to premium 5-layer woven polyester and vinyl fabric. It has the security and impact resistance of a hard cover, but it rolls up fast when you need full bed access. The blacked-out fabric top gives it a seamless look that stays tight and aligned each time you roll it up.



Nothing bulky or awkward here—the side rails are angled at 15 degrees so the cover sits just 1/2" above the bed rails. That gives your truck a clean, flush appearance while cutting down on wind drag and noise. The aerodynamic fit also helps improve fuel economy while keeping stake pockets open for accessories like tie-downs or bed rails.

Whether it’s freezing cold or blazing hot, the Sentry keeps its shape and protects your cargo. The polyester and vinyl fabric layer is tested to handle temperatures from -40°F to 120°F and resists UV damage, dirt, and moisture. Rubber weather seals run along the edges to block dust and rain from getting in, keeping your gear dry through all seasons.
Opening and closing the cover is easy with slam latches at the tailgate—you just press down to lock it in place. Two additional latches at the mid-point of the bed lock automatically with the tailgate latches for extra security. When the tailgate is closed and locked, your bed is fully secured, protecting tools or equipment from prying hands.


Installation doesn’t get much simpler—bolt-on clamps hold the in-bed side rails securely with no drilling required. The self-leveling design keeps everything perfectly square so the cover rolls evenly every time. Need to take it off? Use the quick-release guides to remove the entire cover in seconds without tools. With a weight capacity of 400 lbs evenly distributed, it’s built tough for daily use without losing convenience.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.











Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product