Timbren Rear Suspension Enhancement System
This item does not fit your vehicle
2005 Ford Excursion
These items fit your vehicle
2005 Ford Excursion
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Heavy trailers or bed loads can make the rear end sag and take weight off the front tires. The Timbren Rear Suspension Enhancement System adds 2,000 lbs of rear support to keep things level when towing or hauling gear. The hollow rubber springs work with your factory suspension to hold the vehicle steady so steering, traction, and braking stay consistent even under heavy load.
Uneven pavement or washboard roads can beat up your suspension. The Aeon hollow rubber springs act as cushions that absorb the brunt of bumps and rough roads. They work progressively—soft under light loads and more rigid as weight increases—so your ride stays smooth and controlled without bottoming out.
When you corner hard or a crosswind hits, each spring works on its own to support the driver’s or passenger’s side as needed. This independent action cuts down on body roll and sway, keeping your vehicle planted through turns and helping trailers track straight even in gusty conditions.
Installation is straightforward with vehicle-specific brackets and hardware included. The springs replace the factory bump stops and bolt directly to the frame using existing mounting points. There are no air lines, compressors, or adjustments to worry about—just a simple upgrade that adds stability and helps extend the life of your suspension system.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey guys, it's Jake here with etrailer. Today we've got John with us from Timbren. He's gonna tell us a little bit more about what separates Timbren from the competitors. I appreciate it, I'm glad to be here. Timbren is a suspension specialist. We're based in Whitby, Ontario, so we are a true manufacturer in Canada and we offer a wide range of suspension products from light duty, from commercial all the way up to Overlander, Sprinter applications and trailers.
Now we've talked about a few of the options you guys have and we have plenty of options on our website. Right. We've got the SES kits. We've got the axle-less suspension. Right.
We've got your new coil inserts that just came out recently. But what would you say is your bread-and-butter at Timbren Yeah, no, our SES, suspension enhancement system, is definitely our bread-and-butter. Came out in 2011, won a SEMA New Product Award for best truck suspension. And really, the evolution you just mentioned here, you know, starting in 1968 all the way through now, 2024. But the SES kits are really the core of who we are.
And if you, if you would say at, in the level of stiffness on the market, what would you, would you put yourself in more in a heavy duty side for the SES kits or is it more of a lighter duty Yeah, great question. Lighter duty, we certainly can have a product for commercial and heavy duty, but in '82 when SES was introduced, it was purposely introduced for that, that light duty market. So we start with 1500 and again, go all the way up, but by far really popular with that 1500, 2500 crowd. That kinda leads me into my next question. So we talked about, your specialty is kind of in the lighter duty, but do you have an option for the heavier duty for your sprinter vans and maybe for your truck bed campers Yeah, absolutely.
We do have SES kits for truck beds, truck campers with a higher center of gravity. That creates a new kind of set of problems with the sway side to side. So we have severe duty kits for those. And it uses a single convoluted AON versus a double convoluted to tackle that problem of side to side. And the same thing with the sprinter van. It uses a rectangular shape Aon, but it's there to do the same deal that side to side sway because they're so top heavy, it'll eliminate that. Okay. And then we've had an instance here at etrailer that we had a van that was very, very heavy on the one side. Is there anything that you guys can do personally to help, I would say, I guess customize that kit for that particular user Yeah, by all means we would want that individual to contact us. We would ask a couple questions, see where that weight is distributed and we can actually produce an AON with either a stiffer hardness or durometer or a softer durometer and that will help level it out. So yes, we can take care of that for 'em. And I think that'll really, really help people to get their rigs dialed in because who knows what they're putting in the campers afterwards, after they buy 'em. They come from the manufacturer already heavy on that side and they're trying to load stuff on the other side to try to even it out. But knowing that there's a solution that you can customize for your rig no matter what the weight is on either side is really, really cool. Yeah, absolutely. We're happy to take care of 'em and again, there's no charge for that. Awesome. Now to kind of wrap things up, what sets Timbren apart from a lot of other manufacturers out there Well, I think there's a couple things. We're a family run company and our longevity, you can't deny, 1968 to 2024 and our warranty, we have a lifetime warranty regardless of how old it is. We will take care of it, replace it, limited lifetime warranty, and the hundred day money back guarantee. Very cool. And that's whether or not you're the first owner Right. And yeah, we're not asking for receipt, who'd you buy it from It'll be taken care of. Just give us a ring and we'll take care of it for you. Very cool. Well thank you again for meeting with us. Appreciate it. It was a pleasure to work with you. Thank you.
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
Ratings & Reviews
Feels like it was a real help on the suspension but need about a year to get the full opinion on different roads.
Received the Timbren SES kit in today's mail around 11:30AM, already installed on my 2024 F-150 pickup's rear differential before 3:00PM same day. Like always etrailer's fast delivery time and product info with installation video on your website are very helpful. 1st photo OEM bump-stop, 2nd photo OEM bump-stop removed, 3rd & 4th photo Timbren SES kit installed.
Accolade XT 35L - Timbren SES (TFRSDE - 12k support) loaded in the sweet spot.
These Timbrens should be used on F600 and F550 models. Do NOT use the spacers that come in the box. Just install the Timbrens without the spacers and you are good to go. When FULLY loaded (full gas/water and gear), the Timbrens should compress about 1/2”, which seems to be the sweet spot. The end results are as follows:
1. Better bump absorption and much better rebound. The inside chatter is more of a low sounding rumble and the suspension rebound is really quick.
2. Much better sway control and overall stability.
3. The drive feels more balanced front to rear. The rear drop was reduced by 1”. I think that allows the leaf springs and shocks to work in a more neutral position.
These are worth every penny and are a cheap “set it and forget it”way to improve your ride quality!
Added these to my F250 Super Duty. I carry a golf cart on a Diamond back bed cover. Can be a little top heavy. Perfect addition to my suspension- greatly reduced the sway.
Easy to install using basic hand tools, and stopped the "sag" when I hook up my Casita travel trailer
Helps prevent about 1/2" of sag with my 175lb-tongue weight trailer and easy to install.
Great product. The ride and body roll at the rear axle are notceably improved (1989 Ford E350 Class C RV , 27 ft). I give it 4 stars because the installation was slightly complicated due to the rear brake lines needing to be slightly bent to provide clearance for the U bolts supplied in the kit. Great product and wish it came in a 5000 lb version.
2,000 miles in on a trip from the east coast to the Canadian Rockies these work great while loaded and towing. Close to zero bounce while towing, I love them. Unloaded, however, the ride in my 2026 Tundra has gone south. There is a noticeable, abrupt stop of the units hitting the axle when going over any kind of bump. When I get home and back to regular driving, I may just take them off, its that bad.
I've had these on our tow rig for a year now and I added buy them again today if I needed them.these have worked much better than airbags for our coil spring rear suspension to handle the tongue weight of our trailer. The SUV sits level when the trailer is on and it handles bumps and sway better than the airbags did providing much more comfort to us in the vehicle. Unloaded, we don't really notice they are there, unless, we have all the kids and some friends loaded up and you will fell them work when going over bumps.i do all my maintenance on the vehicle's and inspect these regularly and I cant see any wear so far even though we've gone on 6 trips with our trailer with about 5000 miles doing so.
I cant say these are the best for every truck or SUV, but for ours it is the best and I definitely would recommend to others.
Order came fast and right. E-Trailer gets it the first time !!
Installed fit perfect
Well they are exactly what I thought it would be. Hard for me to say it's what I needed yet.
I installed them on a homemade trailer from a salvaged 2001 base model tacoma. Once I get finished building it out and have some weight in it I'll have a better idea. But from what I've seen so far on a couple test drives they should come into effect when needed.
For reference I building an Tacoma based trailer with an ARE Contractor topper with a Naturnest roof top tent on the very top. So to counter and sway these should be very helpful. At least I hope so. I'm not an engineer but I did stay at an Holliday Inn once.
The Timbren SES is a simple solution for rear squat when towing. When hitched to my 30' Airstream Globetrotter (8800 GVWR) with a tongue weight around 1200 lbs, my Silverado 2500HD had a bit more squat than is ideal. I shopped airbags but didn't want to spend ~$2K for the set up and didn't want the hassle of installation and forever chasing air leaks. The Timbren SES literally installs on the Silverado in about 15 minutes. So simple. No bags, no compressor, no wiring, no air lines, no leaks. And WAY less expensive to boot. Just returned form a 600+ mile trip and it towed flawlessly.
A very simple and straightforward installation once you get the oem bumper stops off (had a shop do that)
Timbren worked with me as I had a non OEM frame height (vehicle was lower than stock) to recommend the proper kit. Highly recommend contacting timbren if you are unsure of the proper kit to use. Ride is more stable. It does feel stiffer and less bouncy but am looking forward to seeing how it performs with my truck camper. Truck is a 1998 dodge ram 2500. Brake line over left side of axle needed to be secured to prevent damage.
The Timbren overload spring/bumper was east to install and did what it was supposed to do when I hitched up a camp trailer. These did not negatively affect the ride by any means and I don't have to worry about the troubles with air bags.
Stiffens and corrects kneel in rear end of 2023 Chevy Silverado 1500. You will notice a stiffening of the rear end suspension while unloaded, but it’s a fair trade off to prevent sagging and porpoising while towing. I found it easier to pull the rear wheels and work from the side than underneath the vehicle while installing.
The timbres bump stop is exactly the right height to meet the axel when the trailer is connected with all its weight onto the hitch. I have an Andersen weight distribution hitch and it levels out perfectly. The day picture is with the coach (Winn 2100bh) with factory equipment. The night picture is after the timbres are in place. Looks good.
It has been almost a year since I installed Timbren Suspension Enhancement Systems (DVF350 and DVR350R) on the front and rear of my 2003 Dodge RAM Van 3500. These bumpers replaced the OEM bump stops that were on my van. I like the Timbren bumpers much better than the OEM bump stops because they provide a progressively cushioned response for suspension compression when traveling over significant humps like speed bumps in a parking lot, or curb ramps into driveways. I did not like the abrupt stop the OEM bump stops provided when traveling over the same objects. I installed the Timbren rear bumpers first, and after a few months of use, I decided to add them to the front. In both cases, the front and rear Timbren bumpers were easy to install once the OEM bump stops were removed. Installation required reuse of the factory hardware. On my van, the Timbren bumpers are not always engaged. Under normal load and travel conditions the bumpers are relaxed and about 1/2” away from the suspension landing points. However, their presence is much appreciated and very noticeable when the van is carrying heavy loads or handling significant humps.
2022 F250 Super Duty. Super easy to install. I have about 3/4" gap between the spring and the plate. Time will tell how they impact the ride quality and how much sag they mitigate with my 5th wheel hooked up.
Great upgrade when pulling our 6500lb travel trailer. Helps with sag and control on the road on our Ram 1500. Change the stock shocks and if you choose, upgrade your stock springs, and you'll get the most out of your half ton.
Absolutely Pleased with the TIMBRENS. They were easy to install, and took less than an hour to install both. I noticed a slight stiffness in the ride as the rear bounced over a bad roadway. Towing is great, with a nice level and smooth ride. I am glad that I did not order the heavier duty Timbrens, than what was recomended for my truck. I believe the ride would have been too stiff. If you look at the photos showing the timbrens, the truck is still lifted in the rear, so what you see is a big gap between the rubber, and the steal plate. When the truck is lowered, there's 1" of space as it should be. BTW, I have been purchasing from etrailer for years now, and I have to say that I have never had any issues with any orders. They are my go to folks for all of my vehicle suppension stuff and trailer stuff. You can't go wrong with buying from them.
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
Bigger in diameter than stock parts are. Fought with the Timbrens for almost 3 1/2 hours before we finally had them in. Getting the coil springs back in over them was another joy. The Timbrens are so long, we had to spray them down with the soap/water mix and work them on, knocking the Timbrens out of place a few times. Which told us they were still not seated in the cups correctly. Haven’t had time to drive it yet. Hopefully they are in, or will fully seat when I do drive it.
Awesome product , easy install, can’t believe how much better our liberty handles, would give it ten stars , I’ve even bought the timbren system for several of the vehicles where I work , and if you have any questions the folks at timbren and e trailer are always willing to help !!!!!
First Trip with my new Rockwood Extreme Sport to San Diego went well although I had a lot of sag in the rear. Camper place said I did not need a weight distribution for my 03 Jeep Liberty so I got online and found the TJRL4. I ordered it and had my mechanic put them in. We had to call the help desk as they were slightly to big to pop in so he had us shave the top down a bit to fit. My last four trips with the TJRL4 on my Liberty have been outstanding, sag is not an issue and a much better ride. I think if you do not do a distribution hitch , this is much easier way to go. It raised my jeep up slightly also without the trailer on so that is a plus too. The main result was I feel very confident pulling my trailer with a Liberty which went from Arizona to Montana and back, up hills, down hills etc with no problems at all and I was in total control at all times. I credit this to the way the TJRL4 corrected the sag issue. Great Product.
Ejm
7/30/2018
Awesome!!! No sag or sway!! Makes towing easy with my Jeep!!
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Sierra K.
5/9/2022
The rubber spring fits into the bump stop pretty tightly. As long as it is firmly seated in the cup and bolted on, then it should be fine.