To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re hauling a heavy load or towing, rear-end sag can throw off your steering, braking, and headlight aim. The Air Lift 1000 Air Helper Springs add up to 1,000 lbs of load-leveling support to your rear coil springs, keeping your vehicle level and stable. That means safer handling, more even tire wear, and less strain on your factory suspension when you’ve got gear or cargo in back.
Every load is different, and the Air Lift 1000 lets you dial in the support to match. With adjustable air pressure from 5 psi to 35 psi, you can fine-tune firmness for towing, hauling, or daily driving. Inflate each spring independently with dual air lines to even out side-to-side loads. A manual inflation valve setup is included for easy access wherever you choose to mount it.
These air springs are made from durable molded polyurethane that stands up to real-world use without leaks or sagging. They sit neatly inside your existing coil springs and absorb road shock and sway for a smoother ride. The kit includes two air springs, heat shields, tubing, Schrader valves, and hardware—everything needed for installation using common tools.
Installing extra suspension support shouldn’t be complicated. The Air Lift 1000 fits inside your rear coil springs with a simple process that doesn’t require special tools. Once installed, you can fine-tune ride height by adjusting air pressure until your vehicle sits at its normal unloaded measurement. It’s a clean, reliable setup that makes daily hauling or towing much easier to manage.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everybody. I'm Hellen here at etrailer.com and we're taking a quick look at the Air Lift Loadlifter 1000 air helper Springs. These are designed to fit in between your coil on the rear of your vehicle. And this is a custom fit for the 2006 through 2018 Toyota RAV4. So if you're maybe putting some extra weight into your vehicle and you want to be able to make sure that your vehicle can support it effectively this is going to be a great way to do that. Now I will say it's not going to increase the overall payload or the amount that your vehicle is rated to carry but it's going to help to get you up to the max more safely without really kind of having any adverse effects to the driving or handling of your RAV4.
So, normally whenever you put stuff into your trunk or maybe you're doing a little towing on a back of your hitch, it'll cause some squat in the back of your vehicle, and it could affect how that your RAV4 handles your braking power, steering all that kind of stuff. So by having some kind of extra support for those quail Springs it's going to mitigate that problem. It also helps to sort of cushion the ride and make your OEM suspension lasts a bit longer since you now have another component to take the brunt of that force. But again, it doesn't allow you to increase the weight that you can carry. Just helps you to get up to that Max more effectively, kind of like a weight belt will help you get to your max safely rather than actually letting you lift more.
So this is what you're going to get in the kit. It's pretty simple. Overall, there's really no cutting or drilling required. It does have the quarter inch line that you need to go from the bags to the back of your vehicle. So you'll have the Schrader valves and all the hardware for that.
A T to connect the bags. If you want to have them just matched up together. Some folks like to keep them independent side besides you can make adjustments. If you're going to have an offset load it probably won't be such a big deal for the RAV4. You can T them together and then one valve will be able to fill both, but it's kind of up to you as far as how you want to do that.
I've seen people put those Schrader valves and all kinds of different spots. You can actually use these to sort of replace the hardware for your license plate so you can hide it on your license plate. You can put this behind the door to your gas tank. Put it at your bumper really anywhere. That's handy that you can get access to it to fill up the bags. Now you can also get a compressor to go with this to make sure that you always have air in your bags and you don't have to find a place to actually get them filled up. But, I would think that since this is rated for kind of light duty towing you probably won't really need to have a compressor or any answer unless you're going to be using these all the time. It's pretty expensive to get one. And I just would say that you probably aren't going to need it since this is just going to be there for support. One little trick that whenever you're getting these installed you want to keep the little caps that it comes with these little black guys that goes over the top of that barb fitting because it's going to really help whenever you're trying to get these in between the coils. Basically you'll just want to squeeze the bags down. Maybe even roll them up a little bit but get them as flat as you can. And then put that cap over the top. So it doesn't take any, any more air in and that'll make it a lot easier to fit that in between the coils. As far as the load leveling capacity this does help up to a thousand pounds, but again it doesn't increase your overall weight carrying capacity. They have an adjustable air pressure between five pounds per square inch and 35. So between five PSI and 35 PSI, this is covered by a limited lifetime warranty and a satisfaction guarantee from airlift and they are made in the USA. That's pretty much all there is to it for our look at the airlift 1000 air helper Springs. I hope this video has been helpful in the setting of this is the right kit for you. We do have a lot of other accessories, here at etrailer.com for your vehicles. So be sure to check them out, and thanks for watching..
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews

Daniel
7/1/2022
The product works very well, the video was great, delivery was on time. I am happy.

Victoria H.
1/4/2025
That's awesome Dan! What are you towing with your RAV4?

Toue
4/29/2023
Still working as good as when it was new. A little bit of noise such a squeaking when deflated but besides that it works great

Lazer S.
7/20/2026
Glad to hear they are making towing a more comfortable experience, Mark! Cool little camper as well! ^___^ Where did you guys take it?

Christopher H.
9/17/2026
Thanks for all of the detail here Charlie and really appreciate the photo!

Gwendolyn Y.
4/10/2025
The helpers look great on your Hummer, Rob! What kind of travel trailer are you hauling?


Rob
4/11/2026
I have towed my RV several times over the last year and these helper springs work perfectly! I had a very small air leak but I added some silicone at the airline connections and it is 100 percent! I carry a battery powered air compressor with me and it’s basically a “set it and forget it” systems.

Lazer S.
1/13/2026
Glad they are working well for you, Scott! I gotta ask, did you do the AHC delete as it was worn our or did you just not particularly like it? I've heard people do this for either reason.


Arthur
9/25/2025
The air springs are still operating as well as the day I installed them. They do not leak any air pressure nor have they degraded in any way. What a great and simple solution that lasts.

Donnie M.
6/16/2026
Well, after going back and forth - basically it comes down to - 60 day drive warranty doesnt compute. So after spending $300 on install, now Im expected to spend another $300-$400 to have them removed to return them, oh and pay for return. So roughly $800 to get back $130. Ill chalk this up to understanding that if a product doesnt work out in any manner. To remove these, you have to take the rearend of the car off - shocks and springs - then try to get the bags out of a much smaller ending without damaging otherwise youll not refund. Basically no support, other than a were sorry.


Gwendolyn Y.
5/20/2026
Thanks for the great follow-up review, Jimmy! Glad to hear the system made such a noticeable difference in both ride quality and suspension support, even when you’re not towing. It’s also great to hear the install videos helped out along the way. Air connections can definitely be the most finicky part of the install, so we appreciate you mentioning that for others considering the setup. Sounds like the end result was well worth the effort on your Pathfinder. Thanks again for sharing your experience a year later!

Big B.
8/3/2021
Still working great no leaks would buy againfor any senna rear with coils...

Big B.
4/2/2026
5 years later still working great hold air wo leaks and prevent bottoming while towing 3000 lbs
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Gabriel
8/2/2024
Still working like first day about 440 miles on it with the same pop-up camper.