See what our Experts say about this Ventline Accessories and Parts

• Adding a Battery to a Snowmobile Trailer for Interior Trailer Lights
  Start with mounting a battery. Since the trailer is enclosed, it would be a good idea to mount it on the trailer frame using a battery box like # 329-HM318BKS. Next, you will need to have the right kind of connectors on the truck and trailer. I would use a 7-Way RV style if you do not already have them on the truck and trailer. There is a 12 volt circuit on a 7-Way. You can run a wire from the 12 volt circuit on the trailer side connector to the positive battery terminal. The battery should...
  view full answer...
• How to Install a Ventline Ventadome Roof Vent with 12 Inch Fan Powered Lift
  You can utilize a power wall remote switch # VC0533-03-A or # VC0533-02-A (black or white). A rocker switch # BL0108-00 will work and you will need 2 of them. The installation kit # 344270KITW will come with screws, tape, and sealant. You will also need primary 16 gauge wire # DW02359-1 as well as a ceiling garnish # VA0445-35 I have attached a picture of wiring instructions for you as well. Installation Instructions for the Ventline Ventadome Roof Vent # V2119-601-00. 1.Mark desired...
  view full answer...
  
• Replacement Rocker Switch For Ventline Range Hood PR
  For your Ventline Range Hood PR 100 CFM, you can use either use the Replacement Fan Switch for Ventline RV Range Hood # BL1194-00 if you need the large style rocker, or you can use the Replacement Mini-Rocker Switch for Ventline Ventadome Trailer Roof Vents # BL0108-00 if you need the small style rocker. Both of these switches are rated for 10A, 125/250VAC. Unfortunately neither of these switches are available in white
  view full answer...
• Installing a Battery on a Trailer and Wiring it to Run Interior Trailer Lights
  I recommend a 12 volt car battery rather than a breakaway battery because you may end up needing the larger battery down the road. What you will do is attach a battery box (see link for options) to the trailer frame. From the trailer side 7-Way connector, there will be a wire attached to the pin in the 11:00 position (if looking at the face of the plug). This is the 12 volt circuit. You can attach that to the positive terminal of the battery. It will maintain the battery but it will not...
  view full answer...
• Adding a Trailer Battery to an Enclosed Cargo Trailer
  Start with mounting a battery. Since the trailer is enclosed, it would be a good idea to mount it on the trailer frame using a battery box like # 329-HM318BKS. Next, you will need to have the right kind of connectors on the truck and trailer. I would use a 7-Way RV style if you do not already have them on the truck and trailer. There is a 12 volt circuit on a 7-Way. You can run a wire from the 12 volt circuit on the trailer side connector to the positive battery terminal. The battery...
  view full answer...
• Replacement Ventline Model PR 100 cfm Fan Motor and Switch
  The Replacement Fan Motor # BVD0278-00 and Mini-Rocker Switch # BL0108-00 will fit the Ventline PR Range Vent. Being as both the fan and light stopped working at the same time I recommend checking to verify you have power coming into the range vent and do not have another issue which is preventing them from working.
  view full answer...
• Replacement Rocker Switch Compatibility with KIB Systems Monitor
  The Replacement Mini-Rocker Switch for Ventline Ventadome Trailer Roof Vents # BL0108-00 is a basic 10 amp switch allowing for a single function. It is designed to fit in a hole that is 3/4 inch by 1/2 inch. If that meets your criteria for your KIB Systems Monitor it should work just fine.
  view full answer...
• Replacement Trailer Vent Fan, Motor, and Switch
  Motor # BVD0218-00 should be the correct replacement. The motor comes with new wires, a bracket, and hardware. The screws that hold the motor to its bracket can be accessed by removing the fan blade. It should just pull off of the motor shaft. You would have to also remove the screen. To remove the screen you may have to remove the ceiling garnish and frame from the inside. It appears you need fan blade # BVD0215-00. For a switch you can use # BL0108-00.
  view full answer...
  
• Replacement RV Fan Motor Recommendation for Motor with MC385MG VD218 Written On It
  Motor # BVD0218-00 would be the correct replacement for what you have. The motor comes with new wires, a bracket, and hardware. If you needed the fan blade you would also want the part # BVD0215-00 and for the switch part # BL0108-00.
  view full answer...
• How to Power Interior Trailer Lights on a Trailer Not Powered by a Tow Vehicle
  First, you need to make sure that the lights you will be using are compatible with a 12 volt system because that is what a battery will produce. Since the trailer will not be connected to a tow vehicle for power, you can wire in the lights independently from a trailer connector. What you will need to do is mount the lights and route the wiring to a switch, like # BL0108-00 if you want them to come on at the same time. You will need to make sure to ground the lights to the trailer frame....
  view full answer...
• Control Panel Switch Replacement for Aux Battery on 2006 Fleetwood Jamboree
  Assuming that the existing switch that controls the auxiliary battery on this control panel is a 10 amp switch that is 3/4" long x 1/2" wide, the Replacement Rocker Switch # BL0108-00 will work to replace your broken switch. If you have a switch with a different amp rating or size, please let me know what those specs are and I will work to find an alternate recommendation.
  view full answer...
• Recommended Replacement Rocker Switch For Ventline Range Hood
  Thanks for the picture! I have an option but The Replacement Rocker Switch # BL0108-00 is only capable of on-off and will not work for checking the capacity of your tanks. You will need the Mini-Momentary Switch # 37213725 which will fit the same 3/4"x1/2" switch cutout opening but is designed for the on-off-on function you are looking for.
  view full answer...
  
• How to Hardwire the MaxxFan Deluxe Roof Vent w/ 12V Fan Part # MA00-07500K
  In order to determine if the wires for a vent fan are already ran in your 2018 Flagstaff Ultralight 29RKWS, you would need to obtain the VIN and contact the trailer manufacturer as we would not have this information. However, if you do not already have pre-existing wires to attach the MaxxFan Deluxe Roof Vent w/ 12V Fan part # MA00-07500K to then this will not be a big deal as there are only two wires on the fan that need to be installed. This is the white wire for the ground and the black...
  view full answer...
• Replacement Switch Recommendation for a Ventline V2094 Powered Vent Fan
  I spoke to my contact at Ventline and she said the correct replacement switch for your Ventline Ventadome Roof Vent part # V2094SP-28 would be the Replacement Mini-Rocker Switch # BL0108-00. The Replacement Fan Switch # BV0199-02 that you referenced is for the Ventadome roof vent part number V2128 and would not work for you.
  view full answer...
• Replacement Motor and Switch for Ventline Range Hood PH100CFM
  For the PH100CFM the correct replacement motor is the part # BVD0278-00 and for the switch # BL0108-00.
  view full answer...
• Replacement 12v Motor and Rocker Switch for a Ventline Ventadome Vent V3094-601-00
  We sure do Mike and thanks for the information. For your Ventline Ventadome Vent item # V3094-601-00, you'll need the Replacement Mini-Rocker Switch item # BL0108-00 and the Replacement 12V DC Motor item # BVD0218-00. These are both factory parts that are exact replacements for the ones that came on your item # V3094-601-00 vent. They are exactly what you need to get your fan back up and running. Here are some other replacement parts we have for the Ventline Ventadome Vent item # V3094-601-00: Replacement...
  view full answer...
• On/Off Switch for a KiB Services Panel
  The Ventline # BL0108-00 switch you referred to is very similar but fits a cut out hole measuring 3/4" X 1/2" instead of the 1" X 1/2" sizing that you want. The closest items we carry are, JR Products # 37212595 uses 1-1/8" X 1/2" cut out (very close) JR Products # 37213405 uses 1.125" X 0.55" cut out (not as close)
  view full answer...
• How is Ventline Rocker Switch Replacement Accessed for Removal
  When removing a switch like the part # BL0108-00 from a Ventline roof vent there is a tab on the top and bottom of the switch that needs to be pressed for the switch to be able to be pushed out. You'd have to access it from above if you can't find a way to reach and and grab it from the topside.
  view full answer...
• Installing 3rd Brake Light And Dome Light For Leer Canopy On 2011 Ford F-350
  To install the 3rd brake light and the dome light on your Leer canopy to your 2011 F-350 you will need to do a couple things. First, there is a wire under the hood on the driver side that is blue and orange. You can tap into that for the brake light on your camper. You will need a circuit tester like part # PTW2993 to test the wire and make sure it only shows power when the brake pedal is pressed. To connect the dome light, you can do that a couple different ways. The best way in my...
  view full answer...
  
• Wiring Installtion of Dome Light and Brake Light on a 2015 Chevrolet Silverado 2500HD Truck Topper
  There are a couple of places you can get the correct circuit to use to wire up the third brake light and dome light for your camper shell. You can use the stoplight switch at the brake pedal of your 2015 Chevrolet Silverado 2500HD. You will need to use a circuit tester like our part # PTW2993 to probe the wires and find the one with voltage only when the brakes are applied. You can also consult the owner's manual for the location of the CHMSL (center high mount stop light) fuse and tap...
  view full answer...
• Replacement Switch for Ventline Roof Vent # V2094
  The correct replacement switch for your Ventline Ventadome Roof Vent V2094 would be the Replacement Rocker Switch # BL0108-00. This is a direct replacement for your old switch.
  view full answer...
• What Size Hole Does Ventline Switch part # BL0108-00 Fit
  The Ventline switch part # BL0108-00 that you referenced is designed to fit a rectangle hole that measures 3/4 inch by 1/2 inch. You'd want to measure the size of the hole that you currently have for switches to determine if this would fit.
  view full answer...
• Replacement Switch, Motor, and Fan Blade for a Venltine V2094 Roof Vent
  I got you covered, for your Ventline V2094 Roof Vent you'll need: -The Replacement Fan Blade for Ventline Ventadome Trailer Roof Vents # BVD0215-00 for the replacement fan blade, -The Replacement 12V DC Motor for Ventline, Ventadome, and Vanair Fans # BVD0218-00 for the replacement motor, & -The Replacement Mini-Rocker Switch for Ventline Ventadome Trailer Roof Vents # BL0108-00 for the replacement switch.
  view full answer...
• Replacement Switch and Fan Blade for the Replacement 12-Volt DC Fan Motor
  The switch is not included with the replacement fan motor # BVD0218-00. You can use switch # BL0108-00. For a fan blade there are 2 options that fit the motor depending on the type you need. First we have the replacement fan for Ventline Ventadome vents, # BVD0215-00. And we have the replacement for Vanair vents, # BVD0217-00.
  view full answer...

Do you have a question about this Accessories and Part?