Replacement Switch for Ventline Roof Vent # V2094

Question

Question:

I need a switch for a bathroom fan #V2094!

asked by: Eric M

0

Expert Reply:

The correct replacement switch for your Ventline Ventadome Roof Vent V2094 would be the Replacement Rocker Switch # BL0108-00. This is a direct replacement for your old switch and will turn on your fan.

expert reply by: Sarah H

0

Answer 1

It is possible that the wires are already ran and you won't have to worry about running wire, it's worth looking into before committing to running wires; the best way to obtain this information is to get your VIN number, and contact the…

view full answer...

Answer 2

The correct replacement motor you would need for your V2094 Vent is the part #BVD0218-00 that you referenced. Based on what you described it sounds like you may have damaged the old motor when you attempted to clean it.

view full answer...

Answer 3

I went out to our warehouse and measured the switch knockout on the Replacement Screen Frame with Screen #BVC0573-41 for you. The knockout is 3/4 inch by 1/2 inch as you assumed. If you want the switch integrated then use #BVC0573-41R in polar white…

view full answer...

Answer 4

Most likely the wires are soldered to the existing switch #BL0108-00 on your Ventline Roof Vent. To remove the wires you can either use a soldering iron like #PTW2000 on the wiring just enough that you can pull them free or if there is enough extra…

view full answer...

Answer 5

When removing a switch like the part #BL0108-00 from a Ventline roof vent there is a tab on the top and bottom of the switch that needs to be pressed for the switch to be able to be pushed out. You'd have to access it from above if you can't…

view full answer...

Answer 6

As long as your existing vent is part #V2092, V2110, V2094 or V2119, the replacement screen you mentioned would work great for you. As you can see in the photo I edited for you, the screen frame does feature a knockout that can be removed so that the…

view full answer...

Answer 7

I spoke to my contact at Ventline and she said the correct replacement switch for your Ventline Ventadome Roof Vent part #V2094SP-28 would be the Replacement Mini-Rocker Switch #BL0108-00. The Replacement Fan Switch #BV0199-02 that you referenced is…

view full answer...

Answer 8

The Replacement Mini-Rocker Switch for Ventline Ventadome Trailer Roof Vents #BL0108-00 is a basic 10 amp switch allowing for a single function. It is designed to fit in a hole that is 3/4 inch by 1/2 inch. If that meets your criteria for your KIB…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Replacement Switch for Ventline Roof Vent # V2094

Product Page this Question was Asked From

Continue Researching