To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Protect your vehicle from mud, rocks and road debris with this pair of mud guards. Extremely durable, thermoplastic construction is both weather and impact resistant. Sleek, contoured design and black finish pair for great-looking, functional guards.
Features:
Husky Liners' custom-molded mud guards are tailored to perfectly fit your vehicle's front fenders. They are longer and wider than traditional, factory mud flaps, giving you a mud guard that looks great, fits great and provides the most coverage possible.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2012 Toyota 4 Runner, we're going to install the Husky Liners Custom Molded Mud Flaps part number HL56921. This set comes with two pieces one for the driver and one for the passenger side. Well go ahead and take the driver side and kind of fit it into place. This will allow me to take a measurement or a mark so I know I need to clean from this point to the bottom edge of the paint so that we can apply a clear plastic film. The clear plastic film will go in between the mud flap in the body this will help protect the paint. So, Ill go ahead and take a cleaner here, spray down the area, wipe it clean and make sure we have the entire area dry as we next going to go back with the soap and water mix and apply to the surface.
This will allow us to put our clear film in place and move it around as necessary to get in position. With our soap and water apply we can go ahead and take our clear film and this going to start it up the paper that comes from install kit. With some kind of comfort it for guys started for now we'll go and remove the rest of the paper and roll out the rest of the film.Next we can take a squeegee, a brush or soft household spatula, drag it along the clear film to push out any water or air bubble. Now, while we're letting our clear film dry and set up, we're going to address the mini mud flap. Some application will have will have this mini mud flap.
If you do it will be necessary to cut off the bottom edge of it so that we can install the new mud flap. So, next time well go ahead, remove it, take the utility knife, cut it off and then reinstall it.To remove it weve got two plastic push pins and a Phillip screw. Plastic push pins can be removed by prying the center cap out and then remove in this push pin fastener. We take a tape measure we're going to cut off about approximately the bottom 2. Now, what we're going to do is go ahead and re install it only will only be using the top few fasteners.
Now, we have the mini mud flap reinstalled. Were going to ahead and remove the two inner wall fasteners. Hang on these fasteners that we will reuse them when we install the mud flap. Now, this will give us three attachment points from the mud flap. The inner wall fastener at the top, it will fasten to the bottom and then a mud flap attachment point.Lets go ahead and put a new mud flap in position.
Well reinstall the inner fender well screws. For our bottom attachment point, well be using these screw and fastener supply with our install kit. The fastener will go behind the mud flap and inner fender well. To all three fasteners in position we'll go ahead and tight them down. Now, with all three fasteners tighten down we'll go ahead and reinstall our tire wheel and that complete the installation of our Husky Liner Custom Molded Mud Flap part number HL56921 on our 2012 Toyota 4 Runner. Filename: Page 1 of 1Order #: 144539532 .
Ratings & Reviews
Brian S.
4/20/2015
The mud flaps still look great and have done a great job helping to keep the truck clean. Awesome product.
Ken
11/22/2019
After install I have been very pleased with the fit and finish, they work as they should.
Paul
11/5/2018
It has been a year and the mud guards are secure. No problems.
Chet C.
4/25/2016
They are holding up great.
Doug W.
1/27/2015
Thank you for the note and followup. Its a first for me from any company, frankly! The product is still as I stated, holding up like new, and just no problem whatsoever.
Michael
1/28/2019
Working just fine. No issues.
James H.
8/14/2016
G_R_E_A_T ProductII Would recommend to all.
Jr
1/22/2017
The perfect fitment and ease of installation easy and they are in the same new shape as when installed. Great Product, best product I have every purchased.
Ben
6/10/2019
A year into use the mud flaps have held up well and still look good. These still get 5 stars from me a year later.
Dave G.
3/16/2021
Fit perfectly. Very easy to install.
Do you have a question about this Mud Flap?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ken
11/22/2019
After install I have been very pleased with the fit and finish, they work as they should.