T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118741
Retail:$64.72
Our Price: $45.94
You Save: 29%
Confirmed to Fit
2021 Honda CR-V
All Wheel Drive
Front Wheel Drive
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (700)
- Q & A (0)
- Photos
2021 Honda CR-V - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- 4 Flat
- Trailer Hitch Wiring
- Tekonsha
- Powered Converter
Quickly and easily install a 4-way trailer connector on your Honda CR-V with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily
- Locate connection point in rear cargo area
- Plug in T-connector
- Includes ModuLite power converter to ensure that your vehicle's wiring matches that of your trailer
- Powered module draws power from fuse to avoid overloading vehicle's electrical system
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 5 amps per circuit
- Tail lights: 7.5 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located in your rear cargo area, behind the driver's-side interior trim panel. Once you've plugged in the T-connector, open the fuse compartment beneath the driver's-side dash. Locate the fuse position indicated in the instructions, then insert the included fuse.
Once installation is complete, the 4-way flat connector will be stowed in your rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
ModuLite Powered Tail Light Converter
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
118741 Tekonsha T-1 T-Connector - 4 Wire - Modu-Lite Converter Included
Installation Details
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Defective
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118741
Average Customer Rating: 4.9 out of 5 stars (700 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.by: Matt03/15/2023
Everything showed up right. Installation on my CRV is a little more challenging than others I've done, but the videos were very helpful. I would definitely buy another hitch from etrailer.com and have referred people to them.
by: Charles05/20/2023
2022 HondaCR-V
Quick and informed delivery. Item was as advertised. Will continue to use etrailer.com.
Charles
5/23/2024
Been a year and still working like a charm. Installation requires a little patience fishing some wires through tight spaces but not difficult. Very happy.
by: Jacques 03/23/2024
2019 HondaCR-V
Perfect fit, installed like OEM harness. A bit of work to get behind the rear panel. The only downside is the size of the connector for the trailer. An in-between connector that would make it possible to thread the wiring through the SUV's body, without having to cut the wiring and reconnect each wire individually, would be ideal.
by: Joseph 02/21/2024
2023 HondaCR-V
This product installed fairly easily, and the online installation video was a great help. It's working well for us. The video didn't exactly show how to add the fuse in the fuse panel under the driver's side dash, but a little more poking around online gave me the hints I needed. I'd definitely buy this product again!
by: Pete11/12/2022
2022 HondaCR-V
Wiring little tough to install on Honda CRV. Watch the how to video for great instructions. When they say tight space they weren’t kidding. The hitch was a breeze. This is a great company with the best service. #3 for me from them overat least 10 years.
Pete
11/13/2023
This product works very well. Honda didn’t make it easy to install in a CRV. But the video available was very helpful.
by: Steve 02/19/2023
Everything as expected. Have not installed yet, but instructions look clear. Looks like a quality product.
Steve
2/20/2024
Installation was easy and quick. If you want your Honda CR-V wired for towing, this kit is what you need.
by: Dan N03/21/2024
Works get. Might be a little challenging for a first time DIYer to install. The video is a great resource. Could be better if the module extended into the spare tire well for fuse replacement. But being fused ahead in the car's system should keep me from worrying about it.
by: Erasmia04/21/2024
The product is great except the fuse that is with it does not fit my car. My car takes the low profile mini fuses not the regular mini fuses. I had to go to the store and spend another $[XX].
by: James03/03/2024
Easy to install, and works very well. Nice to have the harness in the vehicle, out of the elements.
by: ARL02/04/2024
This is my 3rs order from etrailer in 15 years, spanning 2 vehicles. They never disappoint. The install instructions that came with this were garbage, but etrailer had an amazing video (as did other sites) showing exactly how to install it. I'll keep coming back.
by: David11/16/2023
The design of the hitch, wiring and directions were excellent. Installation time was as stated. Dropping the exhaust system on a new car was a bit of a concern but after watching the video and following the tips given it was easier than I thought.
by: Gavin R03/30/2024
2024 HondaCR-V
2024 CR-V Hybrid Sport Touring - Product was well packaged with everything needed to install. The video guide was accurate, and allowed for assembly.
by: TomB.06/24/2017
I installed the Draw-Tite 76128 Hitch, the 118741 wiring harness and the 18144 bracket to mount the wiring plug. You can route the plug through the hole that is provided for the factory hitch wiring (it will fit through, but it is tight) and use the bracket to clean up the install. It looks pretty sweet doing it this way.
Tomb.
6/28/2018
I am still very satisfied with the installation as well as the products. They were put to use about a month ago towing a trailer from Central Vermont to Southeast Ohio. That was about 800 miles and absolutely no trouble.
by: Albert 02/13/2024
2018 HondaCR-V
Shipping was fast as always with these folks. Just got it today. I will be doing the install shortly. Not sure if this is my third or fourth hitch from them. Repeat customer. What else can I say but great people to work with. Thanks etrailer!
by: Kevin 05/03/2024
2022 HondaCR-V
It was great I took it out and thinking about installation
thks again Kevin
by: Kathleen10/22/2023
Bought this hitch along with the wiring harness and 4-pole mounting bracket. My mechanic installed and it's been working great! Hauling well anytime needed!!
by: DanW05/19/2019
Honda
Hitch is working great. Installation went well with no issues - had a mechanic do the install. The hitch fits well on my Honda CRV 2018. Flush with rear bumper so no problem with leg scrapes. Support arms are barely noticeable as they sit up close to the underside of the car.
Danw
5/20/2020
After a year of use, the hitch looks great and has performed well. A little car wax helps keep it looking new. Have used it a few times over the year.
by: Gary 11/28/2023
The products were great, and the service was even better. I wish I would have discovered etrailer years sooner.
by: Dave W.10/26/2020
Great product at a great price. Only suggestion would be to have a way to connect to the trailer wiring without having it being closed on by the tailgate of my CRV. I ultimately ran the cable into my spare tire compartment and then drilled a hole out near my trailer hitch and installed a grommet. Works and looks great but I had to cut the trailer connector off the T1 harness to dress the wires through my new hole and then reconnect it. The whole e-trailer experience and products were fabulous. I have a hitch and wiring harness that are as good as the Honda hitch/harness for hundreds of dollars less.
by: Dave09/17/2023
2020 HondaCR-V
This was my second time purchasing trailer hitch and accessories from etrailer. Excellent price, service and the video of the installation was spot on. I would give them 6 stars if I could.
by: Tom12/29/2023
Perfect fit with great instructions. very helpful and knowledgeable customer service. Would highly recommend.
by: David 04/26/2024
great kit eazy to install works great.
by: Brent 10/25/2023
Super easy plug & play installation, and works great. I've been using it for over two years now, and it still works perfectly.
by: Brian04/18/2020
Second time I’ve bought a hitch and wiring harness, first time for 2013 CRV and now for my New 2019 CRV. I installed the hitch myself using car ramps it probably would have been easier with two people but it really is that easy if you are handy with your hands. You just need to take time with the wiring harness as the video suggests. Cost was less than 150.00 for both. My wife got an estimate for her SUV and the dealer wanted 650.00 for install. This was money well spent. Thank you etrailer.
by: Kevin12/01/2019
2019 HondaCR-V
etrailer is the best, thanks for all the vids guys! Makes the install a breeze! Much appreciated!
At the end of the Tekonsha wiring install vid it shows that the fuse was already installed on the vehicle. So sure enough, I turned my lights on and BAMB, my fuse was already installed as well.
I used a couple 2x4's to hold the panels back...
25
700
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Recommended Best Trailer Hitch Receiver When Comparing Options for 2019 Honda CR-VThe Draw-Tite Max-Frame Trailer Hitch Receiver # 76128 , the Curt Trailer Hitch Receiver # C13397, and the etrailer # e98848 are all very similar. They will install in the same location on your Honda frame but they are rated for different load capacities and both of these capacity ratings greatly surpass the manufacturer towing capacity outlined in your owners manual, so I don't recommend making that the determining factor. The Curt # C13397 or the etrailer # e98848 is my recommendation...
view full answer...
- Parts Needed To Install A Trailer Brake Controller On a 2024 Honda CR-V With a Factory Tow PackageSince your 2024 Honda CR-V already has a 4-Way included with the factory tow package you will need our 7-Way Kit # ETBC7. This will plug into your 4-way and includes the wiring for installing a Redarc Brake Controller # RED52VR. The Redarc is my favorite as the small dash mounted control knob provides a much better appearance than the larger control boxes which get mounted to the dash near your legs.
view full answer... - Trailer Hitch Receiver and Wiring Harness For a 2022 Honda CR-V EX-L Hybrid With Hands Free LiftgateThe etrailer Trailer Hitch Receiver # e98848 will still allow for you to use your hands free liftgate on your 2022 Honda CR-V EX-L Hybrid. The range of the sensor may be limited so you will want to move your foot right next to either side of the receiver tube for the best results. I do recommend the Tekonsha T-One Vehicle Wiring Harness # 118741 to be installed with the receiver. This 4-way flat connector will allow you to connect to the lighting on most small trailers or using Auxiliary...
view full answer... - Does Trailer Hitch Receiver for 2022 Honda CR-V Require Fascia TrimmingThe Draw-Tite hitch you mentioned is not a fit for the '22 as of yet, and there is fascia required to install a trailer hitch on your 2022 Honda CR-V, but there is an option for a hitch that fits which has very minimal trimming on the underside of the vehicle: - Curt Trailer Hitch Receiver # C13397 The Curt # C13397, which fits all models (including Hybrids) except for the Touring, only requires you to cut a small 3" x 1.275" section of the fascia for installation. I have added a photo...
view full answer...
- Recommended Trailer Hitch Fit for 2022 Honda CR-V HybridThere sure is! We offer the Curt # C13397 and the etrailer brand # e98848. Both are Class III hitches and both have identical capacities and would install in the same manner. The only difference between the two is that the Curt # C13397 uses a glossy powder coat finish while the powder coat of the # e98848 has a matte finish which makes it a bit less visible, in my opinion. Unless you're particular about the appearance of the finish, I'd recommend choosing the least expensive of the two....
view full answer... - Recommended Hitch for a 2022 Honda CR-VThe correct hitch for your 2022 Honda CR-V is the etrailer hitch item # e98848. This hitch is custom fit and bolts to your Honda with included hardware. It also fits the 2021 model. The etrailer hitch item # e98848 is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity, and a 525 lbs maximum tongue weight. The hitch is made in the USA and weighs 30 lbs. I have linked an installation video along with a couple of pictures so you can see what this hitch looks like when...
view full answer...
- Correct Wiring Harness for a 2019 Honda CR-V LX FWDThe correct wiring harness for your 2019 Honda CR-V LX with FWD is the Tekonsha T-One # 118741 which is compatible whether it's a FWD (like what you have) or AWD. This harness plugs into factory wiring inside your rear hatch area. We have actually performed this installation on a 2019 CR-V so you can check out the attached installation video to see exactly how it's done. If you don't already have a trailer hitch then I recommend the etrailer Trailer Hitch # e98848 because it has a hidden...
view full answer... - Trailer Hitch and Wiring Recommendation for 2019 Honda CR-V for Towing Pop UpThe trailer hitch I recommend for your 2019 Honda CR-V is the USA made etrailer.com hitch part # e98848 as it has great towing capacities, installs easily, and only has the hitch opening hanging below the rear bumper so it's mostly hidden which also helps with ground clearance. I attached a link to an install video as well as a picture of what the hitch looks like installed as well. For trailer wiring the Tekonsha kit part # 118741 is what i recommend as well since it has the easiest...
view full answer...
- Parts Needed to Install 7-Way Trailer Wiring Connector on 2017 Honda CR-VYou will need to start with a 4-way (if you do not have one). For that you would want the # 118741. Now if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way. If you do have trailer brakes you would need the # ETBC7 instead of the # 37185 and a brake controller. This kit comes with everything needed to wire up the 7-way and install a brake controller. For a brake controller I would recommend the Prodigy P2 Brake Controller...
view full answer... - Hitch Fit for 2022 Honda CR-V TouringThe Curt # C13397 hitch you'd looked at isn't a fit for your 2022 Honda CR-V Touring model, but we DO have a hitch fit that will work great for you. I'd recommend the EcoHitch # 306-X7345 2 inch receiver, which is compatible with the CRV-Touring model. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118741, a ball mount like part # 2753, and # 19260 for a 1-7/8 or # 63845 for a 2 inch trailer ball. I've linked to install videos for the hitch and...
view full answer... - Does Curt Trailer Hitch Receiver C13397 Fit A 2021 Honda CR-V HybridThe Curt Trailer Hitch Receiver # C13397 you were looking at is confirmed to fit both the Hybrid and Non-Hybrid models of the 2021 Honda CR-V. The reason you see it listed as fit for both is for our fitguide. While some hitches like the # C13397 fit both models, there are other hitches that only fit the non-hybrid models. If you are planning on towing with your CR-V you will also need a trailer wiring harness # 118741, and a ball mount, hitch ball, and hitch pin and clip which can all...
view full answer... - Will the Curt Hitch # C13397 Fit My 2022 Honda CR-V Hybrid Touring Model?Yes! I am happy to say that the Curt Hitch # C13397 will fit on your 2022 Honda CRV Touring Hybrid model. With the Curt Hitch, it is assembled here in the U.S.A., so you can rest assured of its quality. If you plan on towing with your CRV, I recommend a ball mount/ball like the ones included in the Curt Towing Starter Kit # C45534. Not only does this come with a ball mount and ball, but it also comes with a hitch cover and locking hitch pin. To complete the setup, I recommend the T-One...
view full answer... - Recommended Hitch And Wiring For A 2022 Honda CR-V With All Wheel DriveFor your 2022 Honda CR-V EX-L with All-Wheel Drive, I recommend going with our American made etrailer.com Class III Hitch # e98848. This will require some trimming to get installed, but once it is fully hooked up it will only have the receiver tube exposed. The matte black finish also makes it less obvious, so it will be the best option for you. For the wiring, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118741. This is a direct plug and play option and I have found Tekonsha...
view full answer...
- Trailer Hitch Recommended for 2018 Honda CR-VI'd recommend going with a Class III hitch, because their 2 inch receiver size is the most common and would provide the greatest selection of hitch mounted accessories like bike racks or cargo carrying trays. When the capacity, the hitch appearance once it's installed and cost are compared, I'd personally choose the Curt Class III, part # C13397. The hitch is a concealed crossbar design, which means that the only portion of the hitch that will be visible from the rear is the receiver...
view full answer... - Best Trailer Hitch Receiver for 2019 Honda CR-V Towing and Bike Rack UsageI recommend the etrailer Trailer Hitch Receiver # e98848 for your 2019 Honda CR-V. The matte black finish will blend in better with the trim of your vehicle. The hidden cross tube design will better conceal your hitch on the rear of the CR-V. And with the 2" receiver will allow for you to use a wider range of bike racks. The etrailer Ball Mount Kit for 2" Hitches # 989900 will provide you with a 1-7/8" and 2" ball. You can then choose from the 2 ball mounts included on which rise or drop...
view full answer... - Recommended Hitch for a 2022 Honda CR-VTo add a hitch to your 2022 Honda CR-V, I recommend the Curt item # C13397. This hitch is custom fit and bolts to your Honda with included hardware. This is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity and a 525 lbs maximum tongue weight. I really like the Curt item # C13397 because the crosstube mounts behind your rear bumper cover leaving only the 2" receiver exposed. This not only looks better but it helps with ground clearance. I have linked an installation...
view full answer... - Will the etrailer Hitch # e98848 Fit My Hybrid Model 2022 Honda CR-V?Yes! I am happy to report that the etrailer Hitch - 2" # e98848 will fit a Hybrid model of 2022 Honda CR-V. If you need a wiring harness to complete your setup, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118741. This harness will provide your trailer with basic running light, turn signal, and brake light functions. Also, this harness is designed to work with front-wheel and all-wheel drive models.
view full answer... - Will the Auto Lift Gate Sensor Function on my 2022 Honda CR-V Touring w/ the Curt C13397 Hitch?I would be happy to answer your questions. The Curt Hitch Receiver item # C13397 is a confirmed fit for your 2022 Honda CR-V Touring. According to Curt there have been some redesigns to this hitch to make it more compatible with the auto lift gate sensor. Originally, the hitch didn't work with the hands-free liftgate feature, but Curt has redesigned the hitch so it is more compatible. The way this hitch mounts the only portion of it that would potentially block the sensor is the 2" x 2"...
view full answer... - Trunk Mounted Bike Rack For 2020 Honda CR-V To Carry 2 Step Through Cruiser BikesThe Saris Bones 2 Bike Rack # SA805BL will fit your 2020 Honda CR-V. It will allow you to carry 2 bikes up to 35lbs each. You will need an adapter for your step through bikes. I recommend the Yakima Tube Top Bike Adapter Bar # Y02531 as it has the largest range of adjustment(14-1/2" to 31-1/2"). The T-One Vehicle Wiring Harness # 118741 will allow you to use Auxiliary Lights # C53201 on the back of the bikes. This will let drivers behind you have a set of lights they can see clearly...
view full answer... - Comparing Trailer Hitches For 2019 Honda CR-VSo there are a few important differences between the Draw-Tite Trailer Hitch # 76128, Curt Trailer Hitch # C13397 and etrailer.com Trailer Hitch # e98848 that fit your 2019 Honda CR-V, which I'll go over for you. The first difference is the look; as you can see by the accompanying photo, the Curt and etrailer hitch have a concealed crosstube while the Draw-Tite has an exposed crosstube. What that means is the tube (the main body) of the Draw-Tite hitch is going to be visible while the...
view full answer...
- Does Curt Trailer Hitch for 2021 Honda CR-V Come with Trailer WiringThe Curt hitch that fits your 2021 Honda CR-V part # C13397 does not include trailer wiring so you'd have to order that separately like with the # 118741 which has the most reliable converter box as well as the easiest install. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch...
view full answer... - Will The etrailer e98848 Class III Hitch Work With A 2021 Honda CR-V HybridYes, the etrailer Class III Trailer Hitch, # e98848 is a confirmed fit for all models of the 2021 Honda CR-V. If a trailer wiring harness is needed too, I suggest the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, # 118741. And for a ball mount, I suggest the Draw-Tite Ball Mount for 2" Hitches, # 2753 using # 19260 for a 1-7/8" ball, or # 63845 for a 2". And hitch pin # PC3. Please note the product review and installation videos linked below.
view full answer... - Does the Curt C13397 Hitch Fit the 2022 Honda CR-V Hybrid ModelYes, the Curt Trailer Hitch Receiver # C13397 fits the 2022 Honda CR-V Hybrid model. It can be confusing sometimes but essentially it is saying that the hitch will fit both the Hybrid model and also if you do not have the Hybrid model. So don't worry, the # C13397 is confirmed to fit your Hybrid model. If you plan to tow you can pick up the T-One Vehicle Wiring Harness # 118741 and the etrailer Ball Mount Kit # 989900 to round out a tow package.
view full answer... - Hitch Receiver and Wiring Harness for a 2022 Honda CR-V HybridYes, we do have a hitch available for the 2022 Honda CR-V Hybrid. I recommend the etrailer Trailer Hitch Receiver item # e98848. This hitch is a confirmed fit for your Hybrid Model CR-V. It is custom fit and comes with all necessary hardware to install on your vehicle. I have attached a couple of pictures of this hitch installed on a Honda CR-V so you can see what it looks like after install. I have also linked a video and the instructions so you can see and understand the process. If...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Video by:
Andrew K
Video by:
Kathleen M
Video by:
Dustin K
Video by:
Jonathan Y
Edited by:
Lindsey S
Installed by:
Jeff D
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Chris R
Test Fit:
Randy B
Test Fit:
Brent H
Test Fit:
Robert C
Test Fit:
Conner L
Test Fit:
David F
Test Fit:
Ryan G
Test Fit:
Bradley B
Updated by:
Wilson B
Updated by:
Isabelle B
Written by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Matt
3/17/2024
Have had this hitch on for about a year. Paint is chipping and its already rusting. Looks terrible already. Kind of disappointing.