Most Popular TorkLift for Toyota Tundra

very secure and super easy to install on my 2021 tundra. The front ones were a little tricky to install but also very secure.

This was a perfect fit on my 2017 Tundra. Installation took about 30-45 min per side. The most difficult step was threading some bolts through the frame holes. They hide nice when not in use.

Click to Enlarge

Click to Enlarge

Click to Enlarge

A bit challenging even for a person with a lot of experience with tools. They want you to fish the bolt and washer through the frame and the mount at the same time, not going to happen with only 2 hands so i went to ace hardware and got some neoprene washers to slide over the bolts to hold them in the frame holes, then gently slid the mount onto the bolts. The drivers side bolts cannot be fished through the tight turns inside the frame with the washer attached to the bolt so getting the washer on the bolt while inside the frame was difficult. I was also concerned that my side exit exhaust would be in the way but as shown in the picture it wasnt an issue.

Click to Enlarge

I recently purchased tork lift camper tie down for my 2012 tundra. shipping was quick,while waiting for my tie downs I put some blaster on my bolts and let it do its job. I did the job on the ground with the help of my son. Totally installed in a little over 2 hours. Great product as are the other items I've ordered from etrailer. I certainly will use and recommend your services to others. Thank you

The front tie down mounts did not fit my 2008 Toyota Tundra SR5 5.7 L V8.The problem is that the bump stops attached to the rear cab mount bolts are in the way. That is something that cannot be removed permanently to accomodate the tie downs. The arm that bolts higher on the frame needs to be bent at a greater angle to fit both the frame and the cab Mount bushing.The rear fit perfectly.

They hold on well so that campers doesn’t fly off.

these fit my '21 toyota tundra perfect. It took a little bit to figure out the instructions but once we got one side, the other side went well. two of us installed front and rear mounts in a little over an hour. I had Torklift on my 2002 tundra and they were very secure for my slide in, that's why I got them again for my new truck.

The rear camper mounts took 10 minutes each to install. The front ones took 22 minutes each. The mounting brackets are well built and designed. It would have been nice if the install instructions we’re online so we could have read them before we received the mounts.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Rear tie downs for my 2001 tundra little more complicated to install than front by myself because you had to wedge between of tight access and old hitch receiver and frame. Although, once installed… worth every penny. Having camper attached to frame makes for less too heavy and more off-road capable. Drives fine in wind at 75mph

The lady who took my order gave me a delivery date of Thursday, 10/13/22. The email that immediately followed my phone conversation confirming my order gave me a date of 10/14/22. I am very disappointed because I schedule to have the Torklifts installed today.

Product did not fit correctly need modifications spoke with TorkLift. They are looking into the problem. Very disappointing would not buy again.

Install was pretty straight forward, they can only go on one way, They bolt right into position right in the same mounting holes that are used for your rear trailer hitch. An extra bolt is supplied for the 3rd bolt position. Each side took about 15 minutes. Very happy with the way it looks and they are easy to access.

Waited a year to buy these. Torque lift true frame mounted truck camper "brackets" I had an unusual truck...Tundra 2015 longbed single cab.(somewhat rare). PERFECT FIT! The amazing part: ordered on tuesday TWO DAYS later there here! Thanks Etrailer, I will buy my next items (fastguns) anchor "binder" kit from etrailer soon . Thank you.

This was my second set I bought. They are very well made and work excellent for my truck camper.

Great product, installed last night! Only suggestion I would have is info on the items page regarding install fitment. I was going back and forth in which model to get because unsure what hitch type I had. All my questions were answered once I opened the manual that came with the product and saw the picture! Would suggest including those pictures of the installed mount on the website.

A little tougher to install than the front ones but not too bad. Torklift tie downs are very well made, tried he bumper attached one but I guess bumpers aren't what they used to be I saw bending at the tie down after one trip. So bought these. Entrailer as usual priced well and fast shipping.

the rear set also fot the 2021 Toyota Tundra CrewMax with minimal modifications. Nobody claims any fitment for these on the rear of a CrewMax, but i GUARANTEE it fits. Mine works great.

Fast, friendly service. Great quality

The hardest part of the installation was removing the frame bolts from the truck that are reused. The instructions were clear and easy to follow, and each piece fit perfectly where it was supposed to go. You don't need to be a mechanic to get these installed, but the proper tools are a must, along with a good chunk of an afternoon.

All parts arrived in good condition. The Torklift part you recommended was the exact fit, installation went well.

Easy to install. Good quality construction. Great customer care when I ordered the incorrect version - was well handled.

fit pretty good and the device for getting the bolts in tough places was brilliant

I originally ordered the incorrect rear Torklifts camper hold downs for my truck. However, I called etrailer and explained my error. They not only helped me pick the correct ones, they sent them out that day. I haven’t installed the rear TC hold downs yet. I was most impressed with the free shipping both ways with no questions asked! I was issued an RMA and the refund came quickly. Very good customer service in an age when there often isn’t any service , let alone great service. The front mounts fit perfectly!

Click to Enlarge

Installed on a Curt 2 1/2 receiver just put on my F350 SD Supercab Diesel SRW 4x4. This bracket does fit this truck with the Curt receiver. I found a little oil on the drill bits and a reamer to remove the last bit of metal from the holes in the receiver helped mount the brackets.

Click to Enlarge

High quality product. TorkLift customer support is excellent. They mistakenly sent me two left inserts for the tie-downs. A quick call to customer support and they sent the correct part right out. Photo shows camper and truck before installation of TorkLift tie_downs.

Click to Enlarge

Well when the box arrived it was damaged missing parts. I think your packaging needs to be do better. Parts were loose in the box. I believe the bracket is overengineneered way to heavy.

The drivers rear didn't get built correctly. the hole to put the tie done is missing. I had to drill a hole into the tie down so I could use it. Didn't notice the problem until I went to put the camper on my pickup. The other three are fine.

Click to Enlarge

Click to Enlarge

Forklift tie downs are manufactured to exact fit to existing manufactured frame rail holes. They lined up perfectly and after 6000 miles with camper on board have stayed secure. The only downside, (this is relative to when and ware you use you camper) they will corrode when driving through snow covered roads that have been treated with sand and/or salt. I use an oil based product to protect them corroding.

Click to Enlarge

Easy to install. Took less than an hour with no helper. They are very sturdy and I expect them to last. 2020 RAM 3500 with OEM hitch.

Click to Enlarge

Click to Enlarge

My brother installed these and he used air tools. The brackets fit perfectly. The instructions were thorough. They bolted right in and the only delay was the disconnect/reconnect of the e-brake cable to install the driver's side bracket (2019 RAM 3500). After all the parts were laid out, he installed all 4 brackets in an hour. He commented many times on the weight, high quality and PERFECT FIT of these brackets. These are worth the price and made in the USA.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I bought both the front and rear tie-downs for my old Lance truck camper on a 2023 Ford F-250. Once installed they work great; very heavy duty. But the thing I liked most was the detailed instructions for installation. Everything needed came with the tie-downs and they were perfectly fitted to my F-250. All I needed was my old torque wrench. Installation probably took less than 2 hours.

The package arrived very quickly and intact. I have a 2020 Ford F250 SD Lariat short bed with a factory hitch. The tie-downs were really easy to install although the hitch adapter plate (see attached photo) which is supposed to attach to the end of the tie-down would not fit inside the tubing on my factory installed hitch so I installed without it and it is tight and snug

Click to Enlarge

I like to thank Lori with etrailer and guiding me through the process of getting , Front and rear, Torklift Camper Tie-downs -Custom Frame Mounts. Well doing research this was the best way to go for tying down and stabilizing a camper. Torklift camper tie-downs are solid well built! I had ordered Mounts on Monday and received them on Friday . I Had the tie-downs on my , 2019 Chevy Silverado 2500 by Saturday. The whole process was awesome , real easy installation. Great help with videos and instructions on mounting tie-downs on my truck provided by etrailer. I’m going to use them on my pop-up Hallmark Camper. Thank you for all your help etrailer.

Click to Enlarge

Click to Enlarge

Click to Enlarge

I bought the TLC2220 for a low profile pop up cabover camper which I had for another Chevy 3/4 ton truck. The prior truck utilized a different attachment but was not available for my current 2012 Chevy truck. The TLC220 offers an excellent attachment point that is made out of thick well made steel and covered with a nice black powder coating. The instructions that came with the product should be thrown away. Pictures are poor, verbiage is incomplete and large gaps in the actual application. The saving grace is the video from etrailer. This is a great video. Complete, simple with no gaps and tells you exactly what the difficulties might be. This video even called out the socket sizes. Unfortunately the mate to this; the TLC 3212 rear mounts has a poor video with again gaps in application. And... again the TLC3212 written instructions is just fireplace starter material.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Front mounts already had signs of use bag of hardware open all over box. Stickers saying front already put on.

Click to Enlarge

Click to Enlarge

These tie downs work great! They were relatively easy to install as well, all of the hardware and bolt feeding tools were supplied with the product. The good thing about these tie downs, is that they are connected to the truck frame and not the truck bed or box, (which is mounted to the frame with rubber mounts) giving too much flexing while hauling a camper.

The product works perfectly!!

Easy install and just a great product. Install took 90 minutes for front and rear mounts.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

These are a must with a slide in. I would not do it any other way. This with a set of fastguns and you're all set.