# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 3
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
This extreme rise ball mount is what I need to make my passenger car into a back-up trailer puller. It is well built and has a welded strut to reinforce the long rise/drop ball mount. The "shock damper" feature is sure to help absorb the leverage movement that a rise/drop ball mount passes on to the hitch receiver itself.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 5
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 7
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 8
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
# 9
Draw-Tite Ball Mount - 9-3/4" Rise, 11" Drop - 9" Long - 3,500 to 5,000 lbs
It's a drop hitch not much to say, exactly what i ordered, and fast shipping.
Basically I bought this ball-mount after I installed the low-slung hitch receiver from ETRAILER to know I have an ability to haul something if really needed in an emergency situation. The receiver hitch was purchased for my Thule bicycle rack , purchased from Etrailer.
# 10
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 11
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 12
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 13
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 14
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
I had previously purchased the etrailer hitch for my 2021 Ford Transit 150. It was a little short in length and the bumper prevented my current ball mount from working. As always, etrailer had the perfect solution. The Draw-Tite is well made and will now remain permanently with the van to be handy whenever the need arises.
It works fine, it's a drawbar. Etrailer is always easy to deal with and decent pricing.
# 15
Reese Trailer Hitch Starter Ball Mount Kit
I needed an very specific ball mount(class I, 1/2" rise, 2" ball). etrailer had what I needed in stock and available to ship next day. I had the thing ordered in 60 seconds. Wish I wouldn't have waisted my time and gas shopping at my local hardware stores only to find they didnt have what I needed.
# 16
Trailer Hitch Ball Mount 10" Drop, 7,500 lbs
Love “etrailer” !! Always have what is ordered and send the item very timely. I always check with etrailer first as they are well stocked. Thank you etrailer.com!! Also George!
Great price and fast ship.Thanks
# 17
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 18
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 19
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 20
Curt Class III Drawbar - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
A very solid replacement for the stock Bronco hitch. Fits perfectly.
Product appears to be solid but it’s just a paperweight without a locking pin. Since your tow bar doesn’t come with one either it’s just another piece of metal. Product should include locking pin. No satisfied at all
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."