# 1
Pollak 6-Pole, Round Pin, Plastic Trailer Wiring Socket w/ Rubber Boot - Vehicle End
I found what I thought I needed on the website to prepare our car to be flat towed, but wanted to call to verify. After a short phone call, eTrailer saved me about $50 and got me the stuff I actually needed to get the job done! I won’t shop anywhere else!
This part is an exact replacement to the part that failed. The failure was caused by a poor installation which allowed the rubber boot to chaff on the truck frame. As it was an exact replacement installation was straight forward although I modified the mounting bracket to prevent a reoccurrence of the problem.
# 2
Pollak 7 Pole to 4 Way Connector Adapter
Everything worked out well. On time and fits perfect. Attach hitch setup and my new Ridgeline. It comes with a 2" inch receiver and I have a full compliment of 1.25. stuff from my previous car. All from etrailer i must admit! so I needed the 2-1.25 reducer, a good lock, and the 7-4 reducer for my goodies! Thanks for the grest service
I used this outlet plug to have 12 volt to power our shuttle pump on the water wagon to pump chemicals into our chem farm mix tank works really well easy to wire and very nice looking very durable .
# 3
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
Wiring worked perfect for my project. I replaced the wiring on my 14 foot utility trailer. If I was to do it again I would buy the next length up. I would have liked to have a little extra wiring if I was to ever need it.
Worked perfectly with the trailer lights.
# 4
Hopkins Endurance 6-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
The stuff not here
Very difficult to make the wiring connections, I was afraid I’d have problems on down the road so, I took it out of circuit and threw it away
# 5
Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End
Quick shipping, will order from them again!
Exactly what I needed and It's a great fit
# 6
Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector
i had to replace these two items as my dear daughter went down our goat path driveway too fast. they replaced the originals from etrailer from the prior year. shipping is timely and customer service actually helps! i wired from battery to controller to hitch myself, and everything fit.
This product works as expected. There is not too much to the installation, just plug it in properly and mount the ground wire. I did not find an easy way to mount this to my wife's Odyssey, or to the trailer hitch (item# 75270). Luckily, I do prototype design and manufacturing. So I came up with my own solution. I designed and made my own bracket to mount the 7 pole to the trailer hitch. It works like a charm, and looks great!
# 7
Pollak 6 Pole to 4 Pole Connector Adapter
Works really well.
This product wooks great. I will do business with this company again
# 8
7-Way Molded Connector w/ 10' Cable - Trailer End
I upgraded my trailer from hydraulic to electric brakes and rewired everything to neaten and freshen up things. Its a nice piece. I recommend.
The overall quality of the cable is impressive
# 9
Hopkins 6-Way Connector with Jacketed Cable - Trailer End - 8' Long
The plug was missing the set screw and collar that compresses on the cable to prevent strain on the connectors when removing the plug. You can see the set screw clearly in the product picture.
I like this style of plug because it is molded and is important in keeping water out of the plug. It is conveint because it has the right colored wires. I have a water tight termination box with studs that it is wired into. Once I damaged the cable so I opened up the terminal box installed eyelet lugs on the spare pigtail, and installed it in a fiew minuets. I keep a spare on hand with lugs on it so if I have an accident I can quickly replace it. I also use these on some of my smaller tow behind equipment. that's why I like this size plug it isn't real bulky.
# 10
Hopkins Endurance Flex Trailer Connector Adapter w/ LED Circuit Tester - 6-Pole to 4-Pole
I was very glad to find this adapter so I can hook my bumper pull trailer to the wiring that is already in place for the gooseneck. Easy to order, delivered fast. Problem solved. Thanks
Choosing the correct connector for my pop-up camper and F 150 baffled me before I asked etrailer for help. I got that help, bought the etrailer connector, and it worked like a charm. The lube that came with the connector was an unexpected bonus. Many thanks.
# 11
Hopkins Endurance Multi-Tow 7-, 5- and 4-Way Flat Trailer Connector - Vehicle End - Ergonomic Design
Installed the Hopkins muti-tow 7, 5, and 4 way flat connector this morning. I ripped the original connector that was attached to the bottom of the hitch receiver off when I was 4-wheeling into the Doll House campgrounds in the Maze District of Canyonlands a month ago. So, I cut a hole in the bumper and mounted the new Hopkins connector, cut off the old broken connector mounting bracket, and connected the factory wiring to the new Hopkins device. Hopkins product installed easily, looks great, is now out of the way, and has the flexibility of multiple trailer connectors when required. I am pleased with the product. Attached is a photo.
Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.
# 12
Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket - Vehicle End
Worked out awesome. I bought this for a buddy for his used truck. The previous owners for what ever reason took it. Plugged it in and worked flawlessly.
It is a direct OEM replacement, easy installation. What I liked most was a real person answered my call and took my order, Katherine was very polite and knowledgeable. Thanks again. CJ
# 13
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
7 pin connector separated from cable. I was expecting that "Molded Cable" meant that the connector was fused to the cable insulation but instead, the two separated almost immediately after I installed it. It still works fine as the wires are connected securely inside the connector but with the outer covering pulled out like this, I don't think it will last very long.
Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture
# 14
Adapter 7 Pole to 4 Pole with Tester and Cover
ETrailer had exactly what I wanted at a fair price. Website was easy to navigate and purchasing was simple. Shipping was fast and I was kept notified right up to when I received my order.
Plugs in easily, shows that pins are producing voltage, and locks in place using the spring loaded door to the 7-pin.
# 15
RoadMaster 6-Wire Connectors - Trailer and Vehicle Ends
This was easy to install looks great and works excellent. have had on issues with this product my trailer lights are always working and keeping me safe.
Installed a Blue Ox Base Plate kit on a 2015 Cadillac SRX. The base plate arrived promptly and was well packaged considering its weight. Watched the videos etrailer provides and used them as a step by step video guide. The videos were a big help. Installation is not too difficult if you're mechanically inclined. Had someone help with the installation but one person can perform the installation. I think the base plate is well engineered and everything fit as it should. Love the fact the installation is so well hidden. We have about 400 miles on the installation and have had no issues. Thanks to etrailer for a great price, great service, and great product support.
# 16
Bargman 7-Way, RV-Style Connector w/ 12' Long Coiled Cable - Trailer End
Excellent addition. I was having an issue with chaffing the straight oem wiring when towing my gooseneck with my F-550. This coiled wire completely eliminated that problem.
This coiled wire connector is a must for travel trailers as the straight one that came with the trailer drug on the road until it wore through on a busy interstate highway and subsequently locked up the brakes at approximately 60 mph. The way it stopped the truck and trailer I thought the transmission exploded. It would not move until I disconnected the trailer batteries. Make sure you order it long enough as I did not twice! E-Trailer was the best at changing my order before shipping and again when I returned one that I still thought was too short. I still can't say enough good things about how they have treated me through multiple times I have ordered things from them,definitely my go to for anything I need for our trailer.....
# 17
Adapter 4-Pole to 7-Pole and 4-Pole
Really nice trailer wiring adapter. Very easy install. Takes about 30 minutes with all the tools needed. Drill, 7/64 bit for pilot holes to mount the bracket, flat blade screwdriver and 11/32 nut driver and two #10 self tapping metal screws with locking split washers and a couple zip ties to tidy up the wiring harness.
This is a great adapter to retro fit connections on my 2011 Expedition. Simple to instal and great support from etrailer.com.
# 18
Pollak 6-Pole, Round Pin, Trailer Wiring Socket - Exposed Terminals w/ Rubber Boot -Vehicle End
Used this as the connection point for the Roadmaster diode wiring kit. Seems to be well made and will hopefully last a long time. I did spray paint it flat black so it blends into the front bumper of my “toad” a little better.
The documentation for wiring is limited and difficult to read without magnification. Otherwise this is well made and works perfectly.
# 19
RoadMaster 4-Wire Connectors - Trailer and Vehicle Ends
I periodically pull a 12v pressure sprayer behind my lawn tractor. The 12v harness I originally made that clipped to the tractor battery was always cumbersome and became hazardous when it recently shorted out due to rubbing (and no fuse in line). So I finally took the time to do it right, mounted this connector to the rear next to the taillight, and created a hidden fused permanent harness to the battery, and of course utilized the mating connector for the sprayer harness side. This little connector was perfect, high quality materials (connector body and electrical terminals), high spring force on the cover when not in use, nice sealed design yet easy to plug/unplug. Very happy with this purchase and will likely buy it again.
This is not a real easy thing for do it yourselfer. However with the resources provided, if you are ok using tools and are able to watch a video showing step by step you and can do this. The base plate and towing system has been perfect.
# 20
Hopkins Endurance 7-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
Well I wasn't able to use this as there was no good place to install on my car without it practically dragging. Not a product problem at all. I tried to return and customer service was fast and super helpful... unfortunately return shipping would eat up any refund. So.. I get to keep it. good quality and product. Very happy with it and wish I could use it. Will keep it for sometime in the future when of course I will need it.
I bought this socket for my 2006 Volvo Xc90 to wire in the 4-Pole harness I also purchased from etrailer. Already had a few 7 Blade to 4-Pole adapters from my previous vehicle, and wanted the option of adding a trailer brake wire for a small camper later on so that was the main reason for the purchase. It also went very well with the Hidden Hitch I had already installed, bracket mounted right up to the existing tabs on the hitch. Super quick and easy install, as all of my etrailer purchases have been. Looks great on the truck, and functions great with the 180 Degree cover.
What our customers are saying:
"very easy to shop"