Best 2022 Forest River Wildwood X-Lite Travel Trailer Camper Jacks

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.

Sturdy jack, easy to install. We installed it facing to the driver's side so we can still put our tailgate down. Very powerful jack, only drawback is it is very slow.

Showed up a day early. Looks like a perfect replacement.

Works great as a stabilizer. I have a 38' trailer and I use screw jacks to level the trailer. Once the trailer is level I lower the stabilizer jacks to eliminate any movement. With this combination the trailer does not move one bit.

There's not a lot to say. The first Stabilizer carton was damaged to the point the carrier couldn't even find the Stabilizer. etrailer.com was very cooperative & sent a second unit out right away. Although the second shipment packaging was damaged all parts were there and undamaged. I installed the unit and it is so so much better, quieter and faster than the old unit. I highly recommend both Lippert and etrailer.com

After receiving the packages was very severely damaged and there was no Jack.Stand crank and no nuts and bolts.Don't know what else I miss

I bought 2 sets of these to level & stabilize a 7500lb smoker trailer (1 in each corner). though they do stabilize, They don't lift to level it off (meaning by inches), the weight/load rating paired with the word "Jack" is misleading. I had to use other "Jacks" to Level it first. This trailer is stays mostly on the pad I built for it on my property, and they work well once situated.

My Jack arrived DOA. After installing it on my trailer, the Jack didn’t work. The manual crank handle came in handy because I didn’t have time to troubleshoot and repair it at the time. It was just a wire that was no longer connected to the switch but I have to tell you it was extremely disappointing to receive a brand new item that didn’t work. If it had worked out of the box, I’d give it a five star review. You should consider soldering and heat shrinking the wires to the switches or making the wires longer so they aren’t banjo string tight and putting the lug at a strange angle.

Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert

These things make a great trailer jack. A plate on top and your done. Tried bottle jacks, these are great.

Great replacement

Easy to install. Much cheaper than others. Improved side to side rock on 41 ft fifth wheel. Large feet will work well on gravel campsites. Would recommend.

Stabilizers are working great. Reduce the sway and rocking at the back end of the 5th wheel unit. You want to install these before you open the slides or you will be crawling under the slides in the rocks/dirt. Units are easy to setup, tighten the straps, and remove when done camping.

Took the sway out 95%. Excellent customer service! Quality product.

Before I purchased the Strong Arm my travel trailer would shake considerably when someone would move around the trailer. Since installing the Strong Arm system (which was quite easy to do) movement about the trailer is no longer an irritating issue.

Work great and good backup to electrical Jack. Our electricals were not working but now are. Hopefully, they remain as backup as have to handcraft or additional support.

The jacks were well packaged and shipped out fast. I got these to replace tho ones on my camper and they bolted right up.

I should have got one years ago. I only use it when it's connected to the truck with the engine running. This I believe gives me full power. It has enough power to raise the trailer when connected to the truck to get the anti sway bars attached. Sure beats all that hand cranking.

The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.

Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!

Easy installation to replace the manual trailer crank. This model is powerful and works well. It has the ability to be rotated 90 degrees so its sideways. The advantage being is that my GMC 2500 AT4 truck tailgate can be lowered with the trailer connected using it in the sideways mounting position.

I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.

Does not ratchet up, a pin must be manually inserted. It only came with one 6" long pin, which needs to be cut in half to make these stands functional. This is more like a folding jack stand, but the pin is not connected to the stand with a lanyard. I will be cutting the bar in half and welding a washer to hold it in place. I will also need to add a lanyard to it so I don't loose it. I would not recommend this product, but I have not found a better substitute for my application.