Best 2017 Chevrolet Silverado 2500 Trailer Suspension Parts

as stated

These did not fit my 3500 lb axle. It has been very difficult determining the correct size U-Bolts for my axle. It appears etrailer does not carry the size I need.

The lift worked out perfectly,I had the place where I bought the trailer install them because I didn't have a welder to weld the saddle mounts to the axle and that's a must for a safe installation,also I had the place where I bought the trailer do it because they had the capability to align the axle perfect to the trailer after the installation. The lift added approximately 5 inches to the trailer hight so I could install the off road wheels and tires.The lift didn't affect the handling of the trailer at all.

Click to Enlarge

Click to Enlarge

Jaime at ETrailer was extremely helpful and got my order sent up ups ground since I was having issues using a P.O. Box. My parts arrived quickly and fit perfectly. I installed them last week and my trailer looks so much better and won’t be scraping on my driveway anymore!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Great price. Easy install. The trailer is quiet when the suspension is articulating around tight turns and going over speed bumps. And peace of mind knowing the worn out bushings are gone.

Customer service, response, shipping and ease of doing business are all top of class. The product is solid but kudos to the eTrailer staff for helping me out with a quality issue with one of the shackle assemblies. eTrailer has earned all my future business. It's great piece of mind to know they stand behind the products they sell.

We broke down on a Saturday near Cincinnati and couldn't find any parts, so I called etrailer and luckily they had a wet bolt kit in stock. They shipped it next day, which means business day, next day, aka Tuesday " thanks UPS ". I had the kit installed by a mobile mechanic and I was back on the road by 3:30pm.

Click to Enlarge

Had to replace the axles and decided while there, just do the whole suspension too. Got the axles directly from Dexter but purchased the suspension kit from etrailer. Replacing the equalizer was the easiest part of this project and if I didn't have to replace the axles, probably would have had it done in under 2 hours. Time will tell how well it rides and the tires wear.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Very good service and very good parts as usual!

Size I needed and seams good quality

I upgraded my leaf springs to 4000lbs springs and needed longer axle U bolts and Quinn at etrailer was helpful getting the correct bolts headed my way.

Click to Enlarge

Click to Enlarge

These seem to be working ok but do not appear to be designed for use with the HD upgraded Moryde greaseable shackle kit that I purchased with them . You can see in the photos that they rub and bind

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Got the kit today. Some of the nuts were oval and would not fit on the bolt of course. Now I have to go to box store and find nuts that fit! Not very good quality control!!

Click to Enlarge

We have had great experience with eTrailer, These parts came in as described.

Rapid delivery and accurate order with high quality product.

Your shipping time went wrong, but Kelsey’s way of handling My order with problems, made my respect level go up. Also, on your website, you have a picture of equalizers that look American made, with your name on it. What I received was stamped China and looks cheap…..

Ordered a lot of parts for a dump trailer rebuild in Sept. Didn't install some of the final parts until Christmas break. THEY SENT COARSE THREAD NUTS INSTEAD OF FINE. I ruined 2 u-bolts and need all 16 fine thread nuts. I'm outside 60 days so I was told I'm on my own. I've spent $5k+ on etrailer. I'll find some place else.......

Click to Enlarge

Click to Enlarge

Exact replacement for original parts, easy install

Installed slippers Center Point system on out Alpine 3101RL 5ver. The install is straight foreward if your mechanically inclined. Now about the lack of instructions, nothing shipped from Lippert. etrailer provided a link to help with that. I do prefer printed instructions opposed having to scroll through my phone with dirty hands. The torque specs provided by Lippert don't align with normal torque charts for said fasteners. The banana shackles are very thin and unplated,they are just raw steel. For the cost of the suspension Lippert cound do better on the shackles in this kit. Lippert recommends in stalling the air gauge for the air bags outside,however to gauge is a cheap plastic model. I feel it would have a short life span exposed to the elements. The good now, it seems robust and likly to help absorb road shock. I have not had our 5ver on the road yet. But I will leave more feed back when I have. I purchased this suspension system after finding a broken main leaf on our front tandem. I replaced all of our leaf springs bushings and bolts with the wet bolts Supplied in the kit. FYI Lippert neverfail bushings fail in less than 7k miles. We are not over weight.

Just installed the lippert center point and I have to say very impressed on how well it’s built. Super easy to install and I can’t wait to take it down these California roads and see how much better it rides. Installed on a 2022 jayco eagle Ht 29.5 BHDS

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It took some time to install. Here are a few of the 'tricks'. Use PB blaster on old hardware. Use block of wood to pound in the brass bushings. When they will not fully insert, use one of the old bolts to suck it. Remove the ridges on the old bolt to prevent damaging the bushing. Tighten the nut, remove, add washer, tighten nut again, remove, add 2nd washer and tighten nut again.... To fully install new bolt, use a washer to suck in the bolt. Amateur like me can do it in about 5 hours from start to finish. The trailer was lifted with wheels barely off the ground. Removed the wheels and creatively used the jack to lift/lower axle(s) to get the hardware removed/installed.

Nice upgrade kit to replace worn parts on a 3 horse tandem axle trailer. Having the beefier shackle straps, bronze bushings, and ability to grease the moving points is a beautiful thing.

Trash !!!! 4 equalizers and just one it’s holding the weld now I’m losing money because my trailer suspension its not functioning

Click to Enlarge

These fit perfectly on my triple axle Kaufman trailer where I replaced all 4 of them. I got some commercial quality spray paint and painted them black. I'll also include some pictures of my old ones that were original with the trailer. You can see they definitely needed to be replaced! I always use etrailer for my trailer parts. Everything is good quality, fits perfectly, and arrives on time.

Click to Enlarge

Installed these with the Dexter Bronze Bushings and Lippert AP wet bolt kit. No more clanking and banging from the trailer going down the road and especially making tight turns.

Click to Enlarge

These hangers are great for the center. They provide just enough clearance for your equalizer. Because of the length and being that I am a welder I added a support inside the hanger to keep them rigid!

Megan was very helpful with helping get this order together and communicating with parts being shipped from other locations. Thank you so very much Megan!!!!

Install wasn’t bad. Grand design welds a V bracket inside the spring hangers for more strength so that was my only challenge on install. This caused a problem on the center hanger as the spacer wouldn’t fit. Had to grind about a quarter inch off the spacer so it would fit as I could only bend the bottom of the hangers so much. Will be towing about 100 miles this weekend so it will be nice to hopefully not have broken drawers in the back of the trailer as well as shelves in the fridge door dislodged. I also did the X factor cross braces on the front and rear hangers for more strength. Will post back after we get more miles on it, but given all the other positive reviews I don’t think I’ll be unhappy.

Click to Enlarge

Click to Enlarge

Click to Enlarge

OMG! After having the trailer bottom out on the stock springs while traversing a RR crossing, this system has proven to be amazing. Returning from a VA campground I crossed multiple RR crossings and traveled some rough pavement. I found I had left a bottle of shower soap on the ledge in the shower! It was still there when I set up in my yard. Not possible with the stock suspension!

Click to Enlarge

Click to Enlarge

Installed a year ago, I made a drilling template to help locate the frame mounting bracket screw holes. Installed a set on (2) fivers, spent average of 2.5 hours for total installation per fiver. Helped the ride of the trailer. Would certainly recommend the shock kit.

Click to Enlarge

Click to Enlarge

This is a great kit! Everything needed is included. Be sure to purchase the heavy duty wet bolt kit for the shackles.

Click to Enlarge

Trailer is back to new again.

Brandon was very knowledgeable about what I would need to replace my axles and springs, right down to the sizes for bushings and bolts. I have been using trailer for many years because their service is awesome.

Made a nice little trailer to haul wife’s golf cart!

Click to Enlarge

Good kit with the necessary parts to replace leaf spring suspension. I welded the hangers rather than bolting them. The parts are not coated for the price point so you will need to paint them or they will rust immediately.

Click to Enlarge

Click to Enlarge

Our trailer was so low...that it could not make it up a low curb and some driveways - especially when fully loaded. Went with the Dexter axle flip kit. The Dexter bracket and base plate pieces are worth the extra $20-$30 compared to other similar kits - they make fitment easier, eliminate any guesswork on placement, and decrease installation time because of it. Took 2-3 relaxed pace hours for us to do single axle install. Tools required were ratchet/wrench set (13/16 deep socket worked for us for most of the bolts), cheater bar (for working those rusty bolts off), drill, angle grinder (cutter disc for oem u-bolts and leaf spring bolts that are rusted or welded in place, stripper disc for cleaning area around new bracket for welding) welder, floor jack and jack stands. We had to remove the leaf springs, as the wheel mount brackets would not fit through the openings. Was hoping we wouldn’t have to, but it was pretty simple to do. We jacked the trailer up. Removed the wheels. Removed the axle. Cleaned the axle area where new brackets go. Set the height and placement of the new Dexter brackets. We left the OEM brackets on the axle and placed the Dexter ones in the exact same position 180 degrees on the other side. Welded them on. Reinstalled leaf springs. Reinstalled axle, reinstalled wheels. Then voila! We added 6 full inches of height. Super awesome.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Great conversion kit, easy to get the plates lined up perfectly. I welded the new saddles onto the axle and welded the nuts to the bolts so there is zero chance of anything moving. Having the plates held in perfect position while welding made it simple. Solved the "dragging wheels problem" without having to cut off and reweld the fenders (which had been welded without enough clearance to the tires at the factory.)

Click to Enlarge