# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
At 68 yrs old, just single-handedly installed the 50 pound Curt hitch receiver on my 2016 Honda Pilot, using two jack stands and the vehicle's car-jack to position it correctly and hand thread the 6 bolts. Made a bit more room for myself by first lifting the back of the vehicle onto a makeshift ramp consisting of two layered 2x6 board. Also first tried to hand tighten the bolts before placing the hitch under the car and found I had a fair bit of rust to work through with rust blaster and wire brush. Instructions were clear and accurate. One tip, do the center bold on the muffler side first (to be able to slide the unit between the muffler and the frame, then the center bolt on the driver's side second. From there, it is a breeze. Took me an hour to get rid of the rust inside the welded bolts, and then an hour to install the hitch.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
Thus is a good quality ball mount. We have utilized in a 2017 Honda Pilot with an etrailer hitch. It has primarily been used for a bike rack. But no doubt it would work for any trailer that its mounted to. etrailer had the best deals that in found online. I would order from them again.
# 3
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Perfect fit with the hitch and pin. Very substantial heft and feels like quality.
Word perfect. Heavy duty quality product
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The item arrived on time and was exactly what I needed. E Trailer is a great place to fill all my towing needs.
The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.
# 5
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Everything worked exactly as stated. Very easy to install. The videos are great. Shipping was fast. Very happy!!
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
# 6
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
Works great. Tows and EVERYTHING!
Great product! Has everything you need to start hailing items with a trailer. Definitely recommend this product and company.
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I ordered and received the ball mount and sway bar together. They were received very promptly and in excellent shape. They are very heavy, i.e., heavy duty. The bracket that was fitted to the trailer was about half a screw wider than optimal size for my smallish trailer but did fit. Installation was easy. The self-tapping screws functioned well. All-in-all, a 10 out of 10 experience.
# 8
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
definitely solid as a rock
# 9
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
Installation instructions came with the hitch and were clear and easy to figure out. Easy installation, the wiring harness had vehicle specific instructions as well and was easy to install, and everything worked as designed when I tested it. I will buy from eTrailer again!
# 10
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Just what I needed. Shipped and received when etrailer said it would. Not my first order and they are always one of my first visits when I need something for my trailer.
Allows me to open the tailgate on the truck with a trailer hitched up.
# 11
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
trailer hitch works great with no flaws in manufacturing welds. Purchased to drop cycle trailer down 4 " off my honda Pilot. Now trailer is level and goes down the road great.
Delivered early. Great quality. Thank you!
# 12
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
# 13
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
This is exactly what I needed for my front end mounted receiver.
As advertised and quick delivery, I am an Etrailer fan!
# 14
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Great purchase experience. eTrailer has this convenient package of ball and hitch already torqued together, AND includes a locking pin in addition to the normal cotter pin! Website is clear on details of package, contents, and dimensions of each component. Shipping was fast and packaged well. I’m not sure if I saved money compared to buying all this separately, but I’m going to believe I did. Thanks!
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 15
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Great product well made and a nice carry bag.
# 16
B&W Tow & Stow 3-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
This has been one of the best hitches that I have owned. It is adjustable to change between my Jeep Wrangler and my Ford F-150 Limited. Both have different tow heights and tow needs based on trailer type and payload capacity. This hitch has worked great for those purposes!
# 17
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
Nice solid (not hollow) and WELDED hitch. Have logged about 5,000 miles this year with no problems. I had many problems with bolted on balls, welded hitches are the way to go.
# 18
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
A year has passed with my Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount and I have nothing but praise for this mount. Once you find the correct height to have a perfectly level trailer there's no need to adjust. The beauty lies in the cushioning! Towing a Yamaha AR190 (3200lb boat and trailer combo) is silent. Even over the bumpiest pavement the tow is smooth. There is no harsh slamming when braking or taking off from the boat ramp. I don't know why everyone isn't running one of these, I wouldn't run any other hitch mount PERIOD! If you're on the fence, get off and buy one, you will NOT regret it!
# 19
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 20
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"