# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
At 68 yrs old, just single-handedly installed the 50 pound Curt hitch receiver on my 2016 Honda Pilot, using two jack stands and the vehicle's car-jack to position it correctly and hand thread the 6 bolts. Made a bit more room for myself by first lifting the back of the vehicle onto a makeshift ramp consisting of two layered 2x6 board. Also first tried to hand tighten the bolts before placing the hitch under the car and found I had a fair bit of rust to work through with rust blaster and wire brush. Instructions were clear and accurate. One tip, do the center bold on the muffler side first (to be able to slide the unit between the muffler and the frame, then the center bolt on the driver's side second. From there, it is a breeze. Took me an hour to get rid of the rust inside the welded bolts, and then an hour to install the hitch.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
Thus is a good quality ball mount. We have utilized in a 2017 Honda Pilot with an etrailer hitch. It has primarily been used for a bike rack. But no doubt it would work for any trailer that its mounted to. etrailer had the best deals that in found online. I would order from them again.
# 3
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Everything worked exactly as stated. Very easy to install. The videos are great. Shipping was fast. Very happy!!
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Great instructions, very timely delivery!
very high quality and fits perfectly.
# 5
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I ordered and received the ball mount and sway bar together. They were received very promptly and in excellent shape. They are very heavy, i.e., heavy duty. The bracket that was fitted to the trailer was about half a screw wider than optimal size for my smallish trailer but did fit. Installation was easy. The self-tapping screws functioned well. All-in-all, a 10 out of 10 experience.
# 6
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
trailer hitch works great with no flaws in manufacturing welds. Purchased to drop cycle trailer down 4 " off my honda Pilot. Now trailer is level and goes down the road great.
# 7
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
trailer hitch works great with no flaws in manufacturing welds. Purchased to drop cycle trailer down 4 " off my honda Pilot. Now trailer is level and goes down the road great.
# 8
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
trailer hitch works great with no flaws in manufacturing welds. Purchased to drop cycle trailer down 4 " off my honda Pilot. Now trailer is level and goes down the road great.
# 9
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Works great. Tows and EVERYTHING!
Easy installation, low profile and excellent quality. Exactly what I was looking for in a hitch receiver for our 2021 Pilot.
# 10
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
Exactly as described. Well made.
# 11
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 12
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 13
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
Exactly as described. Well made.
Great deal on this, it was almost $20 more locally. Received it fast, it was packaged very well. This looks really clean on my vehicle and I never have to worry about "did I tighten the ball enough".
# 14
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."