Most Popular - 2 Inch for 2014 Toyota Highlander

This is a great ball mount for my Draw-Tite 2 inch hitch. It has a 1 inch ball hole and 5/8 inch pin hole. Mine came with the hitch pin, but I use a locking one that I purchased separately so it would be much harder for a would-be-thief to take. When not in use, I take it off and store it my trunk area. As with the Draw-Tite hitches, this ball mount is very well made and suited to the task of towing. Another great product at a great price!

I am truly amazed by the customer service from Etrailer. I ordered a hitch, ball and hitch plug with standard shipping on Thurs around 11 am. Their pricing was lowest I found. My order arrived the following day. I wish all my orders from other websites were so efficient. I will be using Etrailer.com again. Thank you!

I seldom take the time to write a review but I felt compelled to share my excellent overall experience with etrailer.com. I ordered the C13200 trailer hitch receiver, 2" ball, 2" ball mount receiver, pin/clip, and C56217 wiring harness for my 2017 Toyota Highlander XLE. All arrived in no time and in excellent condition. The installation videos and PDF documents are outstanding. I installed the hitch receiver in roughly 45 minutes - includes time to convince brother in-law to come over to help hoist it into place. Wiring harness installation was a breeze, roughly 20 minutes (again, great instructional videos). I could not be happier with the finished product. Thanks etrailer.com for making this a trouble free installation. If you are considering adding a hitch, etc. go no further, you are at the right place...order away. Its very easy to install and you will save a trailer load of cash!!!

The hitch went on exactly as described in your YouTube video. I got it on in about 45 minutes without putting the Highlander on jackstands. I did it alone and found a scissor jack the perfect means to elevate and support the passenger's side while I attached the driver's side. It seems to go better by attaching one bolt on the driver's side then one on the other side. By the way, your video explains how the washers should go on. The written instructions accompanying the hitch did not. The wiring package did not follow the video OR the written instructions. Both state that the package contains double stick tape that should be used to connect the black box. There was no tape in the package or attached to the black box. I wedged the black box in an open in the body. I think it will be secure and the wire protected from rubbing. Otherwise, i will have to open the compartments up again and apply adhesive of my own. Your video suggested that the wires can be lead from the driver's side connectors to the equipment tray in the back. It can, but the wires are pinched between the plastic body part. Over time, I suspect wire sheath would rub away and ground the connection. I ground away a very small section of the equpment tray. It created enough space to relieve the pinching. By the way, I'm 66. I'm sure kids could install the hitch even faster than I did.

Very happy with it

Trailer hitch looks great, will work great this spring for trailer hauling projects.

Wow e trailer is the best it was so easy to install my hitch and wiring harness just make sure you have 1 extra person to set in the hitch and bolt up, and borrow a torque wrench if needed everything was real easy and the videos are very helpful thanks e-trailer for having the videos as well when you purchase items it makes it great. A+ for delivery too got my hitch delivered fast to with everything. Keep up the good work

I usually don't leave reviews but this case is special because everything was really easy and fast good product, Video instructions clear and all the pieces fit good...

Yes Laura its a good thing. But I do dismount it when not in use lest I smash someones bumper when backing into a parking space. .

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

I purchased this Curt Ball mount 10-1/4" because I also bought ball hitch mounted mud flaps and my existing hitch was too short.This hitch was maybe a little too long, but it should work.I hope this combination will protect my horse trailer from my nasty gravel roads!

With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.

Super solid mount at a great price. Just the right drop for my boat trailer.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

The biggest issue I have is that the video on the receiver said the rise can go up or down. I try to put the ball in the hole in the rise position and it does not seat all the way the way it does in the down position. Not sure if I can Seat by drawing down the nut or not .

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Heavy duty , very good quality.

A small shipping glitch , but they took care of it quickly

I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.

Works fine, maybe a bit too long of a drop for a 2022 Highlander Hybrid

Fast shipping

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks