Most Popular Fixed Ball Mount for 2013 Mercedes-Benz GL-Class

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

Everything, when I need something for my truck I always turn to etrailer. They make it so easy to get the product you are looking for. The quality of their product and the Customer service are the BEST! Thank you.

Great solid forged Ball mount!

I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!

I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.

Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.

Great looking product and fast service as usual. Now I can keep it clean and stored under my seat without the grease and rust issue. The ball mount with the 2" Brophy stainless ball and the Master Lock Pivot Hitch pin work perfect. Thanks, Garland R in Kentucky...…….

Very useful for adding tie down points. Only reason for not giving 5 stars was the need to cut off the extra length and drill new holes farther up for the pins so the units fit better.

As advertised

Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.

Tow infrequently; got new(to us) 2015 RAM 2500 pick up to tow our 38’ touring travel trailer. Have a HD WD hitch & adjustable sway control hitch set up we use for this trailer, but needed a drop hitch for our smaller Travel trailer& misc use haul trailer,,,,both much lighter & do not require the sway control set up. This drop hitch & ball fit the bill perfectly as the needed drop did not provide suffice t ground clearances to utilize the WD hitch mount setup (which was not needed) for those smaller loads. E-trailer worked w us to get the product we needed & an option that was inexpenve but sufficiently rated to pull our smaller trailers! Very happy our results !

This is really nice. Beveled edges so it slips into receiver hitch so sweet. Beautiful welds heavy weight mount for my weigh safe ball. I bought a 10,000 lbs hitch and I wanted a draw bar with the same type rating. Now the only thing limiting my trailer capacity is my truck's ability to tow, not the hitch, bar or ball.

I purchased a Ranch Hand rear bumper for my 2500HD but wanted to retain the use of a receiver hitch. The ball mount would need to extend 8" from the pin hole to even reach the edge of the bumper. This BM29 ball mount works out perfect. The welds look great and the finish is just fine. The only complaint I have is they gained a little length by moving the pin hole a little closer to the end shortening the insertion amount slightly. Not a big deal, it is just noticable next to the other mounts I have at the house.

Product is awesome. Shipping container was destroyed when it arrived. Product was not hurt.

this is a great product that etrailer shipped FAST! i haul a BIG bike hauler all over the east coast and to florida and i needed a solid heavy duty ball coupler. this product is it. i have bought several items from etrailer and every time the service and product is excellent!!

Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

It is heavy duty and well-built. I am not disappointed at all and I get comments everyone smile from people who are used to traveling overseas asking where I got the European style hitch from. The only downside is the lack of interchangeability in the size of the ball itself but I don’t think that’s a big deal because I set it up for what I need it for and keep a vehicle vehicle for longer periods of time.

Solid, heavy as heck. Bought this model because 1) I only have 1 lightweight trailer (Malone xtralight, also purchased from etrailer at the same time) and it’s light weight. 2) I am stuffing this into an adaptor also bought from etrailer to further stuff into a receiver also purchased from etrailer. 3) All this is on the back of my 2018 Subaru Outback. Beings that it’s a Subaru it’s not going to be used to drag a huge or heavy trailer. I’ll repeat this part in my review of the adapter, buy probably from etrailer, a receiver lock that is sleeved, to be both 1/22 and 5/8 and long. That way if you don’t want this sticking way out the back (shin killer) you can use 1 lock and go all the way through receiver/ adapter/ and this ball mount. Otherwise buy you’ll need 2 locks 1 for receiver to adapter 5/8 and a second 1/22 to go through adapter into this unit. A side benefit is it’s just different. It’s not an everyday boring looking ball mount, it’s heavy duty so why not.

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Heavy duty , very good quality.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

I actually got my hitch the date they said it would be here to my surprise. When the box arrived it was pretty much beat up, not the hitch just the box. I wished there was instructions how to install it. Overall very satisfied and will buy from 5hem again

Easy to use and haven't had any trouble towing my small trailer with motorcycle on board. Def recommend.

This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

Excellent hitch easy installation.It only took me about an hr and half to install from start to finish

Very happy with hitch and components, came in a nice tray that I use to store and organize the parts when not in use in the back compartment of my Telluride. All good.