# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I bought this bike rack because I didn't want to have to remove my bed cover every time I wanted to take our bikes on a trip. This rack works perfect because I can roll up my cover and this thing just clamps across the bed. Taking the front tire on and off is kind of time consuming but when I travel with my brother who has a hitch mount rack, it takes him just as long to unload his bike as it takes me to unload. The wheel mounts tighten easily and the bikes appear secure during long drives, so I don't worry about them coming loose. Of course, you'll want to wrap a bike chain around the bike and rack if you plan to leave them out to make sure no one can steal the bike (although it would be missing a wheel)
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
# 2
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 3
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 4
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 5
Softride Shuttle Pad Tailgate Pad for Full-Size Trucks - Up to 6 Bikes - 61" Wide
The fit for a 2014 Ram was spot on, no issue with the wide style tailgate top and the access flap for the tailgate handle lined up perfectly. Material is durable and easy to clean, the only thing holding it from a 5 stars is if it had the padded dividers on top to keep the bikes separated. But for the price, the fit and finish was exceptional, great value !!!
The product review/installation video helped me make my selection. I selected the full size pad for 2001 Silverado 1500. Installs easily, fits nicely, flap in pad is positioned for easy access to tailgate latch.
# 6
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
1 year ago, ordered 2 pair Inno Velo clamp on bike rakes for pickup. One pair received damaged/used. eTrailer credited 50%. Rated average for 2 reasons. First, I couldn't get them to work securely with my tonneau cover without modifications (plastic spacer blocks to clear tonneau rail) and I can't close the tonneau cover over them when not transporting bikes. Second, while not recommended for ebikes, they kinda worked but are not strong enough for the weight of the bikes especially when needing to extend to full length. I like the idea but just doesn't meet my needs. Otherwise, they should work just fine under different applications. Best use is to install and left installed. In my circumstance, removal & reinstallation was a pain.
Using the Grippers for carrying 2 ebikes, weighing 55 & 75 lbs. I know this is above the rated bike weights but so far they have performed well. My short bed keeps the 75# bike pretty well locked in front to back so that may help.
# 7
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 8
Swagman Patrol Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer and 15-mm Thru-Axle
rack tends to work itself loose from bed walls during long trips. had to strap down with ratchet straps to keep from moving. locks only work at a specific angle -- wish the manual had said this because we couldn't lock our bikes until figuring it out.
Excellent Customer service and help for this product. Thank you Carol and Neil your the best.
# 9
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
So far I’ve just assembled it and took a quick test drive around the block. My initial thought is this thing is perfect. It’s super sturdy and easy to use. My only gripe and it’s not fault of the rack, but it’s heavy…
If you've done any research or read any of the other comments on either this rack, or this seller...rest assured they really are as good as everyone says! I ordered my rack on around 4pm est on a Friday afternoon and within an hour I received an email that said they have shipped my product AND upgraded to priority shipping. Can't say enough positive things about the customer service! When the rack arrived, it took me a little over half an hour to get it set up. Probably would e been faster if I were even slightly mechanically inclined (or if didn't I didn't have to borrow a socket wrench from my neighbor). We finally had an opportunity to load up the bikes and head out for a ride today. As others have said, the first time you load up your bikes, it's kind of like a puzzle to get them situated. Took about 15 minutes. This rack is awesome! Very sturdy and the bikes were very secure. Only racks I have had in the past were rooftop fork mount racks. This is so much easier! On e we got to the trail (over an hour drive) getting the bikes off was a piece of cake. Afterwards, it was time to load them back up and it was less than 5 minutes to get them all on and ready to hit the road. There were other 4-bike racks on the website, but this one had enough great reviews that I felt comfortable making the purchase. After the fact, I'm very glad I did! I can't imagine the $800 rack can be that much better than this, and I highly recommend this for anyone looking for a 4-bike platform rack. I will definitely recommend this rack and etrailer.com to everyone I know.
# 10
Swagman Upright Bike Rack for 1 Bike - Roof Rack Crossbars - Frame Mount
Planning on bringing bikes while camping. I mounted 2 of the Swagman bike racks to my new Sportrack on my pop-up camper. The bikes fit perfectly. The racks seem sturdy enough. Not heavy duty, but for my needs they should be fine. Assembly was relatively fast and easy.
We have used the Swagman Roof Rack a number of times when we have needed the additional bike carrying capacity. It took a couple attempts to get the initial spacing of the bike rack properly balanced on the van’s roof rack as recommended by the instructions. But it was easy to do and once set was very easy and quick to put on and take off. The rack works great, the bike is easy to put into place and secure. The bike and rack are very stable and quiet and haven’t required any mid-trip adjustments. We always put the cheapest bike on the roof (lol) but do use a bit of duct tape to protect the finish just Incase. We are very satisfied with the rack and consider it quite a deal for the money.
# 11
Yakima BlockHead Single Bike Truck Bed Mounted Rack - Bolt-on - 9-mm Skewer
Chevrolet Silverado 1500Have used the block head bike mounts by Yakima on trips of 800 to 1500 miles with no incident. Easy to mount the bikes and they have not released even on bumpy roads. Great product for my truck box and bikes are always in view. Easiest way I have found to transport our bikes
With a little adaption the Yakima brackets mounted to my built in bed rails on my 2010 Nissan Frontier. With my truck cap this makes my bikes safe and secure, out of sight out of mind.
# 12
Swagman Chinook Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Truly grooving on my wife's new Swagman Chinook bike rack. She wanted to be able to transport her nice road bike easily without throwing it in the back of her car, and since a roof rack is out of the question, this Swagman model fit the bill perfectly. It arrived quickly on the anticipated date. Kudos to etrailer.com for the email updates to keep me informed of my purchase. Within one hour, it was installed on my wife's 2014 Mazda3 hatchback. The Swagman is heavy and solid, which is reassuring as it makes me feel confident that it will keep the bikes secure. It also makes me feel like I got my money's worth. A ratchet wrench and Phillip's head screwdriver were the only tools required for the easy install. I did my research before purchasing the Chinook model as I was also eyeballing a very similar Thule rack that was slightly more expensive. I spoke with an etrailer.com expert who gave me the lowdown on both models. Ultimately, the Swagman won out because it has a smaller 'footprint' while extended or folded up ... and also can tilt away from the car for easy access to the hatchback area. Very convenient! FYI: Mazda doesn't make a trailer hitch for the Mazda3 as it's a small car with a small engine and has no business towing anything. Thankfully, the Curt company makes an aftermarket frame and trailer hitch that fits the Mazda3 hatchback perfectly with no drilling. Stupidly, I purchased it from another online company thinking I was getting a good deal. Turns out etrailer.com had it for less with FREE shipping. Oh well ... live and learn. Now I know that etrailer.com is one-stop shopping for bike racks AND trailer hitches. (Full disclosure: I had the garage down the street install the frame as it's easier with a lift) Only snafu: the shipment contained an extra set of keys that I assumed was for the hitch bolt lock (there was also a set of keys on the bolt itself). I spent 15 minutes using those keys trying to figure out how to remove the lock from the bolt to install it on the hitch. The keys just wouldn't turn in the lock. I called etrailer.com and Kevin told me to try the other set of keys ... and they worked. So an extra set of keys came with it that did absolutely nothing ... weird! Obviously, I can't speak to the longevity and durability of the Swagman Chinook 2 Bike Platform Rack as I just installed it. What I can speak to is the sturdiness of it, the ease of the installation and my complete satisfaction with the good folks at etrailer.com.
I ordered the Swagman Chinook 2 Bike Platform Rack on line from etrailer and so far have been very satisfied. The bike rack was delivered in less than a week. Unpacking the rack and assembly was fairly straightforward. I have read some reviews that complained the assembly instructions were a bit vague. I didn't have a problem but can see where others without a mechanical background get confused. The rack is very sturdy, but there is some side to side play in the tilt mechanism. I'm not sure this can be avoided with a rack that folds down. Installing the Curt trunk stabilizing strap takes most of the sway out of the rack. Installation is fairly easy and quick. It takes me 6 - 7 minutes to install the back on my hitch, and to install the bike and be ready to drive away. That seems reasonable to me. So far I've only loaded 1 bike. I've included pictures of my installation on a 2014 Mercedes Benz E350 sedan. Clearance between the bikes, the rack and the car are good. With the bike loaded in the inside, most forward position, I have 6" clearance between the pedal and the bumper. With the bike removed, the center support folded flat and the rack folded up in the storage position, I have 4" clearance between the closest part of the bike rack (the fold down hinge assembly) and the back bumper of the car. I am able to open the trunk of the car without removing the bikes or using the tilt feature, but I do have to remove the stabilizing strap first. Overall, I'm very pleased with the bike rack and think it will serve me much better than my old strap on rack. Since the weather has been cool since getting the bike carrier, I haven't taken any long trips to give it a real workout.
# 13
Rhino-Rack Bike Rack for 2 Bikes - 2" Hitches - Tilting
I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.
The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.
# 14
Kuat NV 2.0 Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
Excellent rack, a year later still in great condition. No movement at hitch when driving like other racks. Love the extra bar to work on bike in parking lot. Cracked a part on the rack when backing up accidentally hit it, I called the company and they immediately sent out new part no questions asked and rack is like new. Easy to access the drop and raise bar even with bikes on .A note that with larger mountain bikes only three really fit on the four rack without adjusting handle bars. Thanks to etrailer for stocking a great product and providing excellent post purchase service
My Kuat NV 2. Bike Rack is the best bike rack I have ever owned. It is excellent for electric bikes. Very easy to load bikes and holds bikes very securely.
# 15
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
We love this for our E- Bikes . My husband said once he figured out the parts assembly was straightforward . We used the rack for our RV and it was perfect . Very sturdy and adjusts easily to our bikes . We are very pleased with this rack and would recommend !
# 16
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gray
So after much research into bike racks, I decided on pulling the plug on the Kuat Sherpa 2.0. I've looked into the Kuat NV and other brands, but they were just too much for my needs. If you've got "regular" bikes and not the heavier eBikes, then this rack is perfect. I wanted a hitch rack that was user friendly and not overly complicated. I have a mixed bag of bikes and this rack can handle them all, from mountain bikes, street bikes, and BMX bikes. I like that this rack comes with an adapter piece for 20"-24" wheels. Assembly of the Kuat Sherpa 2.0 is really a no-brainer. I think it's only 4-5 bolts really. Everything else is ready to go. The anti-rattle hitch ball mechanism is simple to use with just a twist of the dial, easy. The tilt pedal/lever is also easy to access should you need to open your hatch, a solid "click" assures it's in place. So far, loving this rack. Fit and finish is superb. Thanks to Jerred and etrailer for answering my questions, always helpful.
OMG!! I have been researching and pricing bike racks for a month. Every time I thought I was ready to pull the trigger, I have a question or review that through me off the trail. I was ready to purchase the rack from outdoor retail store and drive 2 hours to pick it up from store to save the $75 shipping, when I thought about etrailer that I had used when I had a travel trailer. Checked them out, they had the exact rack I decided to buy, with $[XX] discount and free shipping. Life doesn’t get any better. It was delivered right on time and in great shape. BTW etrailers website description and videos were better than the racks manufacturer site. You are Rock Stars in my book. Overall, start to finish was above and beyond expectations.
# 17
Kuat Dirtbag Bike Rack - Fork Mount - Bolt On - 15 mm Thru-Axle Skewer
Cheap alternative compared to having to buy a 9mm thru axle mount for the utili-track in my Nissan Frontier AND THEN having to buy an adapter for that! For under $10 I bought some parts from a local hardware store and made this mount fit the track. It's sturdy, and high quality.
Disappointed. The Kuat Dirtbag works, and feels relatively solid once installed, but is about 2-3 mm shorter than my hub. That means while loading and unloading the fork doesn't sit nicely on the rack and inserting/removing the thru-axle can be quite challenging. I'd heard great things about Kuat's products, and all I can say is I'm glad this one isn't as overpriced as the rest of their lineup.
# 18
Thule Insta-Gater Pro Truck Bed Bike Rack - 1 Bike
Linda and I recently ordered two Aventon Pace 500 NextGen E-bikes from [bike store] in Madison, WI. Not wanting to just toss our expensive new bikes in the back of the p/u when they arrive next month we promptly ordered the Thule Instagator from etrailer. My prior experience with etrailer came as a recommendation from a friend. I was able to do quite a bit of the research on etrailers website, the demonstration video extremely helpful and we placed an order. The racks were in-stock, shipped promptly, etrailer providing a very nice tracking link that included pics of the staff involved in processing the order and a map of the route all the way to delivery. Absolutely 1st rate service. The racks showed up in perfect condition about two days after placing the order, exactly as promised. We are very pleased with etrailer, will most certainly be ordering from them again and recommend this company w/o reservation. Nice job etrailer!
I bought two racks to transport my ebikes. The tires do not fit in the rack. the cradle that holds the tire require to be wider. I need to return them. please assist me in this matter. thank you
# 19
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
This thing is built like a tank! It is of the best fit and funtion I have seen in a bike rack! Solid as can be, fits my bikes perfectly and looks awesome! Plus it folds completely out of the way to access the rear liftgate on my 2022 Rav4!
Great service from etrailer and the rack arrived as expected. Fairly easy assembly. OK video on Kuat’s site, but didn’t cover the foot pedal. Really glad we got the 2” hitch. It tightened up and we’re impressed with the quality and the stability of the rack. We haven’t done a road test yet, but look forward to putting it to the test. We have a Ford F-150 and it works great. The bikes were fairly easy to load with the batteries out and two people. We do need the strap extenders for our RadMini Step Thru’s. The tires are too big for the ones that come with. Only one set of extenders came with the bike and one adapter for a smaller tire. It’s okay, but since it’s a two bike unit, would have been nice to have both extenders. Otherwise, we are really liking the look and stability.
# 20
Kuat NV 2.0 Base Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Matte Black
When I ordered this rack, I was thinking " Wow, this is a lot of money for a bike rack." Now that its assembled and I loaded it with 4 bike's (don't ask me what the bike's cost) I'm thinking "Wow, this is a lot of bike rack for the money". Awesome product and customer service.
This rack definitely has some pros and cons (as do most racks). A minor frustration is that despite ordering the rack and add-on at the same time, the keys don’t match so if locking three or more bikes you need two different keys (this has only really irritated me when it was raining). As other reviewers have mentioned, this thing is heavy. Neither my wife nor kids can lift it to put it on or get it off the car by themselves. The downside is that given the size of the rack it is not real convenient to just leave it on the car. When the rack is in the up position, it is impossible to get in the back so it is necessary to lower the rack each time you want to get in. The other downside is that the rack significantly cuts down on visibility when backing up. All that being said, the rack is rock solid and the bikes are very secure. The rack is great for extended trips. When loaded and tipped down, it is great to be able to open and access the back. The spacing of the bikes is great and I don’t have to spend 15 minutes figuring out how to slide four bikes in just the right spot to make them all fit as I did with my old rack. Best of all the bikes are only sustaining damage on the trail, not on the back of the car! Despite some minor annoyances, I highly recommend this rack. As for assembly, my 13 year old put it together by himself in about 20 minutes (I promised him i would include that fact).
What our customers are saying:
"I purchased a hitch, wiring harness, bike carrier and bike adapter for a newly redesigned 2007 Hyundai Santa Fe. Everything arrived in a matter of days and either fit or worked perfectly. Great prices, quality and service support. Rest assured, I'll be recommending you to anyone who asks. Thanks again."