These brackets let you attach a Sunseeker awning in the top channels of your Rhino-Rack RSP, RS 2500, or SG crossbars. Angled up brackets mount awning above your roof rack. 2 Brackets and mounting hardware included.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey everyone, I'm Ellen here at etrailer.com, and today we're taking a look at the mounting brackets for the Rhino Rack Sunseeker Awning. This allows you to have a secure attachment point from your awning to your roof rack system. This will fit with the Rhino Rack RSP, the RS 2,500, or with the SG roof rack system.Basically we'll have our angled up portion, that's going to attach to our awning with our T bolt. This is going to be an M8 T bolt. It'll actually go the other way, so we can get that T head fit into the slot at the back of our awning, and then secure it with our flat washer and nyloc nut. It's going to be another M8 nyloc nut.
That'll be our attachment point there. And then on this end, this will actually go to our roof rack system. It slides into the top channel of your roof bar. And we'll have our M6 bolt with our flat washer and spring washer, and those will drop down through and then attach into our nut plate on the bottom. This slides into that top channel of your bar, and then we'll have both hardware going through there, so we'll have two bolts going into our nut plate to attach that to the roof rack system.Pretty simple install.
Shouldn't take too long to get set up and then have your son secret attached to your roof. It makes it really nice to not have to worry about mounting anything directly to your roof line, you don't have to make any modifications there. You can just utilize your existing roof rack system for that. Now, if you don't already have a roof rack system, you can pick up any of those Rhino Rack bars that I mentioned. There's a lot of options available here at etrailer.com for just about any vehicle out there.Now, as far as the measurements with our brackets, these are, again, going to be the angled up design, so that raises our awning above our bars to give us better clearance there.
If you would rather them actually sit below the bar, you can get the angle down version. That's available separately using part number RR32127. And you can find that here at etrailer.com.Has a reinforced angle there to make sure that it's going to be nice and sturdy. All the welds are really nice and clean. And as far as the size, which I started it to say and then distracted myself, it's about six and a half inches long, or just over six and a half inches.
About six and nine sixteenths. And then it's about one and a half inches wide, or just over one and nine sixteenths. And about four and three eights inches high, if we count this little angle out. From where this bottom portion is to the very top of it, it's four and three eight inches.They weigh about two and a half pounds. Both our brackets are coated in a powder coating so we shouldn't have any worries about rust or corrosion. These can also work with other flush-style crossbars with that top channel. If you have anything like Tuli or Yakima, it should still slide into place. Our net plates measure about just over three quarters of an inch, about 13 sixteenths inches wide, and about two inches long. These T bolts, if you wanted to use them for another awning besides the Sunseeker, they are about 13 sixteenths wide as well. I hope that helps you determine if this is going to be the right mounting kit for you. And that's going to do it for our look at the angled up mounting brackets for Rhino Racks Sunseeker Awning.
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
These brackets let you attach a Sunseeker awning in the top channels of your Rhino-Rack RSP, RS 2500, or SG crossbars. Angled up brackets mount awning above your roof rack. 2 Brackets and mounting hardware included.This is an excellent product. It only took about 30 minutes to mount.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.