What Size Bolt is Used to Hold On the Factory Bump Stops on a 2011 Ford F-150

Question

Question:

2011 F150 2x4 What size socket goes onto the jounce bumper bolt head?

asked by: Ernie

0

Expert Reply:

The bolt holding on the factory jounce bumper on the 2011 Ford F-150 is a 13mm. You will most likely need an extension to get to the bolt without interference from the jounce bumper.

expert reply by: Michael H

0

Answer 1

We used a 14mm socket to remove the jounce bumper on a 2014 and 2015 Ford F-150. The jounce bumper is about 4 inches long, so you will want to use an extension. I would use a 4 inch extension if you are using a standard socket and a 2 inch extension…

view full answer...

Answer 2

On the surface, there is a lot of similarities between the Curt Spectrum Trailer Brake Controller #C51170 and the Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR, but the Redarc is truly the superior option in every way for your 2019 Audi Q5.…

view full answer...

Answer 3

The Jounce bumper bolt for your 2009 Ford F-150 is a M10-1.5 X 30 mm. With having to replace the jounce bumper bolt it would be a great time to upgrade your Jounce Style Springs! The SumoSprings Solo Custom Helper Springs #SSR-117-40 are…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

Hello John, thanks for reaching out. Since your bed is shorter that 8' we do recommend using a sliding 5th wheel hitch for extra clearance on tight turns. So for your 2020 Chevy 2500 I recommend the following: - B&W Patriot 5th Wheel Trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Bekzod, So while we don't have a way of knowing the exact leaf springs for your Arctic Wolf 5th wheel trailer, I can help you determine the correct replacements. You do have to take a measurement, though it's pretty easy, as all you need…

view full answer...

Answer 11

Hey Joe! We haven't done a lot of installations on the #3460001 and I believe we tied it into a factory switch on the one we did. I would say find any open spot in the dash nearby for installation like the picture below.

view full answer...

Answer 12

Hey Stu, thanks for reaching out! The Weigh Safe Hitch #WS96ZR can definitely be used in the rise position, and the scale will still work in that orientation as well, so you'll be good to go! What are you planning on towing?

view full answer...

What Size Bolt is Used to Hold On the Factory Bump Stops on a 2011 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching