Wiring Diagram For Turn Signal Switch For Peterson Combination Stop And Turn Signal Lights

Question

Question:

DIAGRAM HOW TO WIRE PM 500 SIGNAL SWITCH

asked by: Jesús R

0

Expert Reply:

The wiring color code for the Turn Signal Switch for Peterson Combination Stop and Turn Signal Lights # PM500 is as follows:

Red- Front right
Black- Front rear
Pilot Blue- Flasher - Fuse - 12 volt power
Load Yellow- Flasher
Gray/Black- Stop light switch
Gray- Left rear
Green- Left front

expert reply by: Bryce D

0

Wiring Diagram
(click to enlarge)

Answer 1

Hi Jeff, Nice choice with the 100 amp hour Go Power Lithium RV Battery #GP99QR as well as the Expansion Kit #34282182. Also, you can absolutely replace your PD9260 with the PD9360 model that is compatible with lithium batteries, and our part number…

view full answer...

Answer 2

The difference between the two models that you were researching is that the #PD9260C is designed for use with lead acid batteries and the #PD79RR is designed for use with lithium batteries. Choosing the incorrect battery profile can lead to issues…

view full answer...

Answer 3

The following wires on the Turn Signal Switch #PM500 are for the following functions: Red - Right Front Black - Right Rear Pilot Blue - Flasher - Fuse - 12V Power Load Yellow - Flasher Gray/Black - Stop Light Switch Gray - Left Rear Green - Left…

view full answer...

Answer 4

I spoke with Peterson, and they informed me your lights may not be working because you are going to need to use a 3 prong flasher with your: -Turn Signal Switch for Peterson Combination Stop and Turn Signal Lights #PM500. Additionally, if you are…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 12

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Wiring Diagram For Turn Signal Switch For Peterson Combination Stop And Turn Signal Lights

Product Page this Question was Asked From

Continue Researching