Wil the Electric Ground Control TT Automatic Leveling System Work On a Grand Design Imagine TT

Question

Question:

Will the LC762126 Electronic Ground Control TT Leveling System work with my 2021 Grand Design Imagine 2600RB?

asked by: Steve B

0

Expert Reply:

The Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System part # LC672136 should be a great option for a Grand Design Imagine Travel Trailer. That said, we really don't have a way of verifying fit so the best option would be to take a look through the included instructions and verify you have space for the c-jacks in the spots they need to be. There are really not that many fit issues with the system so odds are in your favor but it's a good idea to do your due diligence beforehand.

expert reply by: Conner L

0

Answer 1

Yes, you can use a Hitch Receiver Reducer Sleeve #C45405 safely with your Reese Steadi-Flex Weight Distribution System #RP66560. I do recommend using the Hitch Receiver Immobilizer #BX88312 as this will eliminate all the play with having the…

view full answer...

Answer 2

When the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 is installed on a trailer and in the fully retracted position it will add 5 inches to the bottom of your trailer frame. So you'd lose right at 5 inches…

view full answer...

Answer 3

The TorkLift GlowStep Camper Scissor Steps w/ Landing Gear #TLA7802-8000 that you referenced uses two pretty easy to remove pins between the steps and the mounting bracket. It would be relatively pretty easy to remove and install when needed.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

It sounds like you are going to have to go with the Yakima LockNLoad Platform Roof Tray #Y05048 along with 3 sets of the Crossbar Clamps #Y05039 to fit on your Yakima OverHaul HD Adjustable Truck Bed Ladder Rack #Y01151-58 on your 2023 Ford F-250…

view full answer...

Answer 6

Hey Dan, yes the rear tie downs that come with the Torklift Tie Down set part #TL34VV do bolt to the trailer hitch at the rear of the truck. I attached a picture that shows our installer bolting it in that area.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, we do. What you are describing sounds like the Inner Frame Brackets for Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Hitch item #RP27FR. I have attached a picture below. These come welded to the frame exactly where you…

view full answer...

Answer 9

No, I am sorry it does not. I just spoke with Lippert and none of the Curt Helux Shock-Absorbing 5th Wheel Pin Box like item #C73RJ are compatible with gooseneck adapters like the Anderson Ultimate 5th Wheel Hitch. You would need to use a standard…

view full answer...

Answer 10

Good afternoon Nathan, that's a great question! You can use the etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers #e38FV with a 3" to 2" reducer adapter like Buyers Products 3" to 2" Receiver Tube Adapter…

view full answer...

Answer 11

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Wil the Electric Ground Control TT Automatic Leveling System Work On a Grand Design Imagine TT

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching