Dimensions Of The Mounting Brackets On Sliding Under Platform Pontoon Boat Ladder 315-FOG3

Question

Question:

What are the dimensions for the mounting brackets. Need to understand the footprint required for mounting. Thanks

asked by: Gordon K

0

Expert Reply:

I attached a diagram that shows the various dimensions of Sliding Under Platform Pontoon Boat Ladder - 3 Steps - 34-1/2" Tall - 400 lbs - Stainless Steel # 315-FOG3. The mounting brackets measure 11-7/8" long, 12" from outside edge to outside edge, and the brackets are 1-5/8" wide. I also attached a demonstration video for you.

expert reply by: Andrew N

0

Boat Ladder Dimensions
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 3

Hi Mike; can you send me your axle information? Is it a 3,500 lb axle? If I had to guess it is likely a 3,500 lb axle on there right now. Assuming you have the standard 3,500 lb bearing combination you can use the DeeMaxx Disc Brake Kit #DE66YR. This…

view full answer...

Answer 4

If you're wanting the size of the pre-drilled mounting holes on the #315-FOG4 they are 1/4". If you're looking for the distance between the mounting holes I have attached a diagram below showing the measurements.

view full answer...

Answer 5

The Taylor Made StepSafe Dock Steps - Triple - 25-1/2" Tall - 300 lbs - White #TM85ZR is the largest that we currently carry in this style. I may have a few other options that will work for you, but they will be quite a bit different. The first…

view full answer...

Answer 6

I have attached a diagram I made of the bolt dimensions of the Jif Marine Telescoping Drop Ladder with Hand Grips - 3 Steps - 34" Tall - 400 lbs - Stainless Steel item #315-EQB3. The pre-drilled mounting bracket with 1/4" holes are spaced…

view full answer...

Answer 7

You could use pvc pipe and secure it to the frame of the trailer, but that is way overkill and way more work then you need to do to protect the wires. I would just get some wire loom the correct size for however many wires you have to run, and some…

view full answer...

Answer 8

Thank you for the photo and you definitely need some suspension help there on your 2008 Toyota Sequoia SR5 with the sag you have. Since you have the SR5, so long as your Sequoia does not have auto leveling, the air spring system you need is from Air…

view full answer...

Answer 9

When it comes to trailer taillights the terms waterproof and submersible are somewhat interchangeable. If a taillight is considered submersible that means that the internal circuits are waterproof and would be protected for if you were to back the…

view full answer...

Answer 10

Since your 2016 Toyota Sequoia is the SR-5 you need the Air Lift 5000 Kit #AL60786. The other kit is for a non-SR-5 Sequoia. If you'd like the ability to monitor and adjust your air bags on the fly I recommend installing the Air Lift Air Shock…

view full answer...

Dimensions Of The Mounting Brackets On Sliding Under Platform Pontoon Boat Ladder 315-FOG3

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching