Recommended Trailer Hitch for a Grand Design Solitude

Question

Question:

Im looking for a hitch to mount on the back of a 2019 Grand Design 310 GK. 3000 lbs 300lbs tongue minimum.

asked by: Joe T

0

Expert Reply:

The Adjustable Width Trailer Hitch Receiver for RVs part # 13703 is what I recommend for a Grand Design Solitude. It features a 3,500 lb gross trailer weight capacity and 350 lb tongue weight rating. This will be the most offered for a trailer as frame strength starts to become a factor past this. It can be bolted-on for an easy install.

expert reply by: Conner L

0

Answer 1

Hey Larry, The PullRite OEX Super 5th-Wheel Hitch #PUL79ZR base weighs in at 101 lbs so you're dropping the overall weight by 42 lbs by removing the top part. If you want something lighter we have the PullRite OEX SuperLite #PUL89ZR which has a…

view full answer...

Answer 2

I'll start off by saying that I don't normally trust the VIN decoders available on the internet when it comes to being accurate with capacities and such, and the highest payload capacity I've seen in my research for the 2011 Chevy…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 8

Hey Rob, the Torklift camper tie downs part #TL87DR that you referenced are the correct tie downs for your 2024 Ford F-250 long bed with a factory hitch and will work with any of the steps we sell. The only ones it doesn't work with is the…

view full answer...

Answer 9

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Recommended Trailer Hitch for a Grand Design Solitude

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching