Is There a Trailer Jack Wheel That Uses Ball Bearings

Question

Question:

Do you have a jack swivel caster wheel with a 2 receiver that has ball bearings? Other types just dons turn with washers as pivot points. Thanks

asked by: Mark L

0

Expert Reply:

The vast majority of trailer jack wheels don't use traditional steel ball bearings as they aren't really meant for rotation speed but rather weight bearings. I am not aware of any options which use traditional steel ball bearings. The Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack part # UF49-954035 uses nylon bushings which provide a smoother than normal rotation.

expert reply by: Conner L

0

Answer 1

I do have an option for you to replace the bottom plate of your trailer jack with a wheel assembly. The option I have is the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks - 1,200 lbs #PS1400750340. This corrosion-resistant,…

view full answer...

Answer 2

Yes, the Replacement Caster Wheel #UF49-954035 that you referenced is compatible with trailer jack inner tubes that measure 1-3/4" in diameter. This is verified in the attached review video.

view full answer...

Answer 3

Jack caster #BD500245 does not feature a ball bearing swivel. Instead, it uses a combination of a thrust washer and a flat washer for the swivel feature.

view full answer...

Answer 4

Since the wheel on your jack is removable you can definitely replace it! Just let me know what the diameter of the inner tube of your jack is along with the pin hole diameter and I can make a recommendation. For example, the removable wheel #DL22539…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Answer 11

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 12

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Is There a Trailer Jack Wheel That Uses Ball Bearings

Product Page this Question was Asked From

Continue Researching