Does Trailer Jack Caster BD500245 Have a Ball Bearing Swivel

Question

Question:

does this caster have a ball bearing swivel?

asked by: Michael B

0

Expert Reply:

Jack caster # BD500245 does not feature a ball bearing swivel. Instead, it uses a combination of a thrust washer and a flat washer for the swivel feature.

expert reply by: Sarah L

0

Answer 1

I spoke with my contact at Fulton regarding the part number you provided, but unfortunately he could not find that part number listed for a Fulton jack. He did tell me that the Bulldog Removable 6 Inch Caster, #BD500245 will fit all 3,000 lbs Fulton…

view full answer...

Answer 2

There are not any caster wheels that we carry that are rated for that 5,000 lb capacity. My recommendation for a durable wheel is the Replacement 6" Caster Wheel #BD500245. This is rated for 1,200 lbs and is the strongest caster we carry that…

view full answer...

Answer 3

Yes, for a jack wheel that will fit the Bulldog Round, A-Frame Jack part #BD1700100317 you can use the Bulldog Removable, 6" Poly Caster Assembly for 2" Jack Tube part #BD500245. Please note that adding a wheel to an a-frame jack will…

view full answer...

Answer 4

Hi Steven! The pin that comes included with the Replacement 6" Caster Wheel for Bulldog Trailer Jack with 2" Tube Diameter - Qty 1 #BD500245 is a 3/8" diameter pin that has 2-3/4" of useable space. We don't have a direct…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Does Trailer Jack Caster BD500245 Have a Ball Bearing Swivel

Featured Help Information

Miscellaneous Media

Continue Researching