What Type of Grease for Lubricating Trailer Jack

Question

Question:

The weld on trailer jack, what kind and/or type of lubrication do you use, i.e.,gear lube, heavy grease? Thanks

asked by: Richard

0

Expert Reply:

I am not totally sure which jack you are referencing but most jacks are designed to be lubricated with white lithium grease like part # L11354.

expert reply by: Jameson C

0

Answer 1

The Curt 45951 Rebellion Shock absorbing ball mount which we offer as part #C83WR would certainly reduce much of the shock and vibration that's experienced when towing a trailer which would absolutely make towing a more pleasant experience. Much…

view full answer...

Answer 2

Yes, your trailer with corner jacks can still absolutely use the Ark stabilizers: - Ark Drop Down Corner RV Stabilizer Jack Kit - 24" Long Corner Steadies #ARK34FR These will weld to the bottom of your trailer's frame, you just need to make…

view full answer...

Answer 3

Good question, and we have asked the manufacturer, Ark, this very same question, and they have said there is not any weight rating for the Ark Drop Down Corner RV Stabilizer Jacks - 33" Long Corner Steadies #ARK77FR. They say the reason they…

view full answer...

Answer 4

We don't offer a combination leveler/stabilizer jack, but if you're wanting something in a stabilizer jack that is very sturdy, you can't go wrong with the ARK Drop Down Corner stabilizer jacks. They're available in a powder coat or a…

view full answer...

Answer 5

You certainly can install two pairs of the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR on your trailer. In that case we recommend adding one jack to each corner of the trailer frame. Keep in mind that these are designed to stabilize, not lift…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

The 3JX and 3JE are most likely a manufacturing stamp number and does not dictate inner or outer. The Bearing #L44649 can be used on either the inner or outer bearing position for your particular hub as there is not a specific one for the inner or…

view full answer...

Answer 8

Based on the pictures you attached and the outer bearing measurement you provided, it appears that you have 1-1/16 inch spindle like the BTR EZ Lube Spindle #TRU44FR. This particular spindle is designed for 2,000 pound axles and will use the same…

view full answer...

Answer 9

According to the Lippert Service Manual for the Lippert Electric Trailer Jack #LC285318. "Maintenance 1. Before each use, inspect the Power Tongue Jack and replace if bent or damaged. 2. If wiring is connected to battery terminal, inspect at…

view full answer...

Answer 10

We spoke with our contact at Fulton and he said the Fulton Jack, #FXPD15L, can be lubricated with any general-purpose grease like our LubriMatic Lithium Grease, #L11316. You can remove the cap at the top of the jack and put the grease in the cap. The…

view full answer...

Answer 11

There isn't necessarily any specific grease to use in the Bulldog Side Wind Jack Assembly #BD182700. You can use the LubriMatic Disc/Drum Brake and Wheel Bearing Grease #L11465 along with the LubriMatic Professional Pistol Grease Gun #L30416. You…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Type of Grease for Lubricating Trailer Jack

Product Page this Question was Asked From

Continue Researching